What to do if my Kolin Water Dispenser is leaking?
If your Kolin Water Dispenser is leaking, the cause may be a loose connection or damaged water pipes. Check the connections and tighten them if necessary. If the pipes are damaged, replace the parts.
Why is my Kolin Water Dispenser not turning on?
If your Kolin Water Dispenser is not turning on, it could be due to an insecure power plug or a tripped circuit breaker. Ensure the power plug is properly inserted and check the status of your circuit breaker.
How to improve the cooling performance of my Kolin Water Dispenser?
If your Kolin Water Dispenser's cooling performance is poor, it might be because the cooling switch is turned off, or the room temperature is outside the specified range. Make sure the cooling switch is turned on and check that the room temperature is within the recommended limits.
Why is my Kolin Water Dispenser not heating water properly?
If your Kolin Water Dispenser isn't heating water adequately, it might be because the heating switch is turned off or there is insufficient water in the tank. Confirm that the heating switch is on and ensure there is enough water in the tank.
Why is the cold water from my Kolin Water Dispenser not cold enough?
If the cold water from your Kolin Water Dispenser is not cold enough, the cooling switch might not be turned on, or there has been excessive cold water usage in a short time. Turn on the cooling switch and wait a moment; cold water should be available again.
Why is the hot water from my Kolin Water Dispenser not hot enough?
If the hot water from your Kolin Water Dispenser is not hot enough, the heating switch might not be turned on, or there has been excessive hot water usage in a short time. Turn on the heating switch and wait a moment.
What to do if the pump is not working on my Kolin Water Dispenser?
If the pump is not working on your Kolin Water Dispenser, it may be because the water container was not replaced within the specified time. Here's what to do: 1. Promptly replace the water container. 2. Ensure the extraction pipe is properly connected. 3. Turn off the hot switch button, then turn it on again.
Includes WARNING, CAUTION, and PROHIBITION statements for user safety.
Specific guidance on operating the dispenser safely and correctly.
Step-by-step guide for unpacking, locating, and setting up the dispenser.
Instructions on how to operate the dispenser correctly.
Procedures for initial setup after installation.
Instructions for routine cleaning of the dispenser's exterior and disposal pan.
Steps for cleaning and sanitizing the water tanks.
Safety guidelines to follow before performing maintenance or service.
This document serves as the owner's manual for the Kolin KWD-BLC-2088B Bottom Load Water Dispenser, providing comprehensive information on its features, operation, and maintenance.
The Kolin Water Dispenser is designed to provide convenient access to cold, hot, and room temperature water. It is a heating and cooling-type water dispenser, offering a reliable and efficient solution for various hydration needs, from refreshing chilled water to hot water for beverages. The bottom-load design simplifies water container replacement.
The dispenser features an electrical display area, an upper door for accessing faucets, hot, warm, and cold water faucets, and a water disposal pan. The bottom-load design means the water container is placed in a lower compartment, with a water extraction pipe inserted into it.
Regular cleaning and maintenance are crucial for optimal performance and water quality.
To Next Page
* Turn off heating and cooling switches.
* Disconnect the power plug.
* Gently rotate the dispenser 90° and move it away from the wall.
* Disconnect the water container from the suction pump.
* Place a 2-gallon bucket under the drain plug.
* Remove the drain cap and rubber to drain hot water (exercise caution, as it will be scalding hot) followed by cold water.
* Reassemble the drain rubber and cap.
* Use the cold faucet to drain any remaining water from the reservoir.
* Mix 3 tablespoons of unscented household bleach or vinegar with 1 gallon of tap water in a clean bucket; let it sit for 30 minutes.
* **WARNING:** Do not use strong bleach or harmful detergents.
* Use a soft cloth soaked in the sanitizing solution to thoroughly wipe the water container cover and the area around the three faucets.
* Fill an empty water container with the sanitizing solution.
* Insert the suction pipe into this container.
* Carefully insert the container into the dispenser.
* Close the cabinet door.
* Plug the unit into a power source.
* Turn on the hot water switch.
* Allow the solution to fill the empty storage tanks.
* Let the solution remain in the tanks for 10 minutes.
* Turn off the hot water switch and unplug the power cord.
* Place a sturdy bucket beneath the drain cap and drain the sanitizing solution.
* Reinstall the drain cap.
* Use the cold and warm faucets to dispense any remaining sanitizing solution into a pitcher for disposal.
* Fill a water container with tap water and insert the suction pipe, ensuring it's securely connected.
* Insert the water container into the dispenser.
* Close the cabinet door.
* Plug the unit into a power source.
* Switch on the hot water switch.
* Allow tap water to fill the storage tanks completely.
* After 10 minutes, turn off the hot water switch and unplug the power cord.
* Prepare a large bucket and place it beneath the drain plug.
* Remove the drain stopper to drain any remaining water.
* Reinstall the drain cap.
* Activate the cold water faucet to dispense any remaining water.
* The dispenser is now ready for use. Plug it in and turn on hot and cold switches.
* If a vinegar or chlorine taste persists, repeat the rinsing process with another 2 gallons of clean water.
* Return the unit to its original position and replace the water container.
The manual includes a troubleshooting guide for common issues:
For persistent problems or other concerns, contact the Kolin Service Hotline.
General| Brand | Kolin |
|---|---|
| Model | KWD-BLC-2088B |
| Category | Water Dispenser |
| Language | English |