Need help?Do you have a question about the Komatsu WA320-7 and is the answer not in the manual?
General| Transmission Type | Hydrostatic |
|---|---|
| Engine Model | SAA6D107E-1 |
| Breakout Force | 50 kN |
| Hydraulic System | Load Sensing |
| Steering System | Articulated |
| Brake System | Hydraulic |
Special safety precautions required for performing work.
Key safety practices to follow during operation and maintenance.
General safety guidelines and warnings for machine operation and repair.
Steps to take before starting any repair or maintenance work.
Specific safety measures and cautions to observe while performing work.
Guidelines for safe lifting, slinging, and signaling operations.
Safety recommendations for operating mobile cranes during machine work.
Safety recommendations for overhead traveling cranes used in maintenance.
Guidance on choosing appropriate wire ropes for hoisting based on load.
Safety procedures for handling air conditioner hoses and tubing.
Measures to prevent fires caused by fuel, oil, wiring, or hot exhaust.
Procedures to follow and immediate actions to take in case of a fire.
Guidelines for the correct and legal disposal of machine waste materials.
Instructions and tips on how to effectively use the shop manual.
Explanation of symbols used in the manual for safety and quality.
Information on the units of measurement used throughout the manual.
Definitions of key terms related to maintenance standards and criteria.
Definition and criteria for allowable clearance in component assembly.
Definition and criteria for allowable interference in component assembly.
Procedures and precautions for servicing fuel system components.
Procedures and precautions for servicing intake system components.
Procedures and precautions for servicing hydraulic system components.
Steps for flushing hydraulic circuits after repair or oil change.
Methods for cleaning hydraulic oil using specialized equipment.
Step-by-step guide for safely disconnecting and connecting push-pull couplers.
Specific instructions for disconnecting and connecting Type 2 couplers.
Specific instructions for disconnecting and connecting Type 3 couplers.
Procedures and precautions for maintaining electrical components and wiring.
Precautions against water ingress into connectors under high pressure.
Preventing contamination when disconnecting electrical connectors.
Cleaning procedures for connectors affected by oil, mud, or dirt.
Detailed steps for handling, removing, installing, and drying connectors.
Visual inspection and proper procedure for connecting electrical connectors.
Specific procedures for handling Deutsch connectors.
Methods for drying wiring harnesses and connectors after exposure to water.
Procedures for handling various types of electrical connectors on the engine.
Specific instructions for disconnecting/connecting BOSCH-3 push lock connectors.
Specific instructions for disconnecting/connecting AMP-3 push lock connectors.
Specific instructions for disconnecting/connecting SUMITOMO-2 push lock connectors.
Specific instructions for disconnecting/connecting SUMITOMO-3 push lock connectors.
Specific instructions for disconnecting/connecting SUMITOMO-4 push lock connectors.
Instructions for handling Cannon-4 turn-housing type connectors.
Precautions and guidelines for handling electronic controllers.
Safety measures during arc welding on the machine body.
General guidelines for troubleshooting electrical circuit issues.
Explanation of electric wire coding system used in circuit diagrams.
Technical specifications and dimensions for wires and connectors.
Table detailing color codes for electrical wires.
Cross-reference of wire types, circuits, and their corresponding color codes.
General cautions to observe during machine operation and maintenance.
Safety guidelines and procedures for removing and disassembling components.
Steps for safely disconnecting face seal type hydraulic hoses and tubes.
Steps for safely disconnecting taper seal type hydraulic hoses and tubes.
Steps for safely disconnecting split flange type hydraulic hoses and tubes.
Procedures for removing O-ring boss type pipe joints.
Procedures for removing taper pipe thread type pipe joints.
General precautions and guidelines for installing and assembling parts.
Steps to take after completing repairs, including refilling and bleeding.
Procedures for checking cylinder heads and manifolds for looseness.
Inspection of engine piping for damage, looseness, and leaks.
Inspection of KDPF, muffler, and exhaust pipes for damage and looseness.
Checking the function and listening for unusual noises from KDPF/muffler.
How to utilize the KOMTRAX system for machine monitoring and support.
Reference table for standard tightening torques for bolts and nuts.
Glossary of abbreviations used throughout the shop manual.
To Next Page