Kongsberg Simrad SY50 - Installation Manual

To Next Page

kongsberg.com/simrad

Simrad SY50

INSTALLATION

MANUAL

Main Page

Table of Contents5
About this Manual13
Simrad Sy5015
Important16
System Description18
System Diagram20
System Units21
Display21
Processor Unit22
Power Supply Unit22
Hull Unit23
Transducer24
Installation Trunk25
Additional Required and Optional Items27
Installation Trunk27
Speed Log28
Course Gyro28
Uninterruptible Power Supply (UPS)29
Operating Panel29
Global Positioning System (GPS)30
Scope of Supply31
General Safety Rules32
Installation Requirements34
Supply Voltage Requirements34
Uninterruptible Power Supply (UPS) Requirements34
Cables and Wiring Requirements35
Compass Deviation Requirements35
Noise Sources36
Dry Docking Requirements36
Requirement for Classification Approval37
Network Security37
Support Information38
Preparations41
Installation Summary42
General Safety Rules44
About Installation Drawings45
Tools, Equipment and Consumables Required for Installation46
Personnel Qualifications46
Rules for Transducer Handling47
Choosing the Best Location for the Hull Unit49
About the Hull Unit Location49
Defining the Fore and Aft Location of the Hull Unit50
Defining the Athwartships Location of the Hull Unit50
Important Considerations Related to Noise51
Sonar Room Requirements52
About the Sonar Room52
Environmental Requirements52
Requirements for Watertight Integrity53
Size and Access Requirements53
Requirements for Insulation, Heating and Ventilation54
Requirements for Electrical Installations, Cables and Communication55
Requirements for Bilge Pump and Decking56
Lifting Requirements56
Acoustic Noise58
Introduction to the Acoustic Noise Challenge58
Contributing Factors58
Self Noise60
Ambient Noise62
Electrical Self Noise63
Reverberation63
Some Means to Reduce Acoustic Noise64
Installing the Sy50 System Hardware Units66
General Safety Rules67
Installing the Display68
Installing the Nexcom NISE 3900E Processor Unit69
Installing the Operating Panel (Mk2)71
Installing the Operating Panel (Mk3)73
Installing the Power Supply Unit74
Mounting the Installation Trunk77
Installation Summary78
About the Installation Trunk80
Rubber Gasket80
Mechanical Support Brackets81
Design and Installation Drawings82
Length of Transducer Shaft Versus Height of Installation Trunk82
Mounting the Installation Trunk85
Cut out a Hole in the Vessel's Hull with a Diameter Large Enough to Accommodate the Installation Trunk86
Orientate the Installation Trunk Correctly, and then Weld It into Position86
Brace the Installation Trunk to the Hull Plating and the Surrounding Hull Frames86
By Adding Several Strengthening Plates86
Verifying the Quality of the Installation87
Depending on the Shape of the Hull, We Recommend that You Fit a Steel Blister for Protection87
Inspect the Installation of the Installation Trunk, the Blister, Hull Plating and All Surfaces Thoroughly87
Mounting the Installation Trunk89
Installing the Hull Unit90
Installation Summary91
General Safety Rules93
Hull Unit Familiarization95
About the Hull Unit Installation96
Rubber Gasket96
Design and Installation Drawings97
Length of Transducer Shaft Versus Height of Installation Trunk97
Rotating the Mounting Flange on the Installation Trunk99
Installation Procedures102
Unpacking the Hull Unit from Its Transport Box103
Unpacking the Transducer from Its Transport Crate104
Cutting the Transducer Shaft105
Making Recesses for the Set Screws Used to Mount the Cable Gland Assembly107
Mounting the Transducer Flange108
Mounting the Trunk Bearing110
Mounting the Gantry113
Mounting the Transducer116
Mounting the Hull Unit on Top of the Installation Trunk118
Lubricating the Transducer Shaft Sleeve119
Inspecting the Transducer121
Verifying the Quality of the Hull Unit Installation124
Hull Unit and Transducer Alignment126
Cable Layout and Interconnections127
Read this First128
Cable Plans129
Topside Cable Plan130
List of Topside Cables131
Sonar Room Cable Plan132
List of Sonar Room Cables133
Comments134
Options136
Installing the SY50 Cables137
Prerequisites for Cable Installation138
Installing the Topside Cables138
Installing the Sonar Room Cables140
Processor Unit Front Panel Description: Nexcom NISE 3900E141
Processor Unit Rear Panel Description: Nexcom NISE 3900E142
Operating Panel Connectors (Mk2)145
Operating Panel Connectors (Mk3)145
Cable Drawings and Specifications146
C22 AC Power Cable147
C24 Control Cable148
C25 Transducer Cable149
AC Power Cable Using IEC C13 Inline Socket150
Ground Cable152
RS-232 Serial Line Connection Using Three Wires153
RS-232 Serial Line Connection Using Five Wires154
Used as Synchronization Trigger (Input or Output)155
RJ45 High Speed Ethernet Cable (1000Base-T)156
K-Sync Interface to Generic RS-232 Synchronization Input157
Simrad TU40 Interface to Generic RS-232 Synchronization Input159
About Serial Lines161
Setting to Work164
Setting to Work Summary165
Inspecting the Installation of the SY50 System167
Visual Inspection of the Display167
Visual Inspection of the Processor Unit169
Visual Inspection of the Operating Panel170
Visual Inspection of the Power Supply Unit172
Visual Inspection of the Hull Unit173
Checking the Environmental Conditions in the Sonar Room175
Making Sure that All SY50 System Cables Are Properly Connected176
Turning on the SY50 System for the First Time178
Making Sure that the Operating Power Is Correct178
Installing the Operating Software179
Obtaining and Installing a Software License for Additional Functionality180
Setting up the Operating Panel (Mk2)181
Using more than One Operating Panel to Control the Sonar (Mk2)184
Using a Single Operating Panel to Control more than One Sonar (Mk2)188
Turning on the Entire SY50 System for the First Time192
Turning on the SY50 System for Normal Use195
Placing each Sensor in the Vessel Coordinate System197
Dimensional Surveying197
Surveying the Transducer and the Navigation Sensors198
Example Procedure199
Vessel Coordinate System202
Inserting the Installation Parameters205
Inserting the Ship Origin and Dimensions205
Inserting the Installation Parameters for the Transducer207
Inserting the Installation Parameters for the Motion Reference Unit (MRU)210
Adjusting the Built-In Motion Sensor Offset212
Adjusting the Stabilization Offsets for the Motion Sensor215
Setting up the Interfaces to Peripheral Devices219
Installing Navigation Sensors and Other Sensors219
Defining the Serial and Ethernet (LAN) Port Parameters221
Setting up the Input from a Navigation System (GPS)222
Setting up the Interface for Speed Log Input225
Setting up the Interface for Course Gyro Input227
Configuring the Sensor Interface229
Setting up the Input from a Motion Reference Unit (MRU)231
Setting up the SY50 System for Synchronized Operation233
Setting up Input from Buoys, Fish Aggregating Devices and Other External Objects236
Configuring the SY50 System for Normal Operation239
Selecting Measurement Units239
Setting up the Alarm Limits for System Protection240
Configuring the SY50 System for Data Recording242
Configuring the Environmental Parameters243
Selecting the Language Displayed in the Menus and Dialog Boxes244
Saving the Current User Settings244
Defining the User-Selected Features on the Operating Panel246
Selecting Which Operating Panel to Use246
Assigning User Settings or Presentation Modes to the Operating Panel247
Assigning Functions to the Rotary Switches on the Operating Panel249
Assigning Functions to F1, F2 and F3 on the Operating Panel (Mk2)250
Testing the Operating Functionality of the SY50 System253
Checking the Hull Unit Lowering and Hoisting Functionality253
Measuring the Noise in Passive Mode256
Verifying System Operation by Means of the Diagnostics Functionality258
Verifying System Operation by Means of the Element BITE Functionality262
Making a Noise/Speed Curve to Determine Vessel Noise266
Creating a Backup with the SY50 Configuration and Software Installation270
About SY50 Software Backup and Restore270
Creating a Computer Image on a USB Flash Drive Using the Acronis True Image Program270
Restoring a Computer Image from a USB Flash Drive Using the Acronis True Image Program272
Creating a Bootable USB Flash Drive Using the Acronis True Image Program273
Installation Remarks275
Technical Specifications276
Introduction to Technical Specifications277
Performance Specifications277
Power Requirements281
Display Power Requirements281
Nexcom NISE 3900E Processor Unit Power Requirements281
Operating Panel Power Requirements (Mk2)282
Operating Panel Power Requirements (Mk3)282
Power Supply Unit Power Requirements282
Hull Unit Power Requirements283
Weights and Outline Dimensions284
Display Weight and Outline Dimensions284
Nexcom NISE 3900E Processor Unit Weight and Outline Dimensions284
Operating Panel Weight and Outline Dimensions (Mk2)285
Operating Panel Weight and Outline Dimensions (Mk3)285
Power Supply Unit Weight and Outline Dimensions286
Hull Unit Weight and Outline Dimensions286
Environmental Requirements287
Display Environmental Requirements287
Nexcom NISE 3900E Processor Unit Environmental Requirements287
Operating Panel Environmental Requirements (Mk2)288
Operating Panel Environmental Requirements (Mk3)288
Power Supply Unit Environmental Requirements288
Hull Unit Environmental Requirements289
Compass Safe Distance290
Display Compass Safe Distance290
Nexcom NISE 3900E Processor Unit Compass Safe Distance290
Operating Panel Compass Safe Distance (Mk2)291
Operating Panel Compass Safe Distance (Mk3)291
Power Supply Unit Compass Safe Distance291
Hull Unit Compass Safe Distance292
Minimum Display Requirements292
Drawing File294
About the Drawings in the Drawing File295
Nexcom NISE 3900E Outline Dimensions296
462682 Power Supply Unit Dimensions298
462683 Hull Unit Dimensions SY50301
489609 Hull Unit Dimensions SY50C304
440475 Installation Trunk Dimensions307
Optional Units310
476352 Operating Panel Dimensions (Mk3)311
440689 Operating Panel Cut-Out Drawing( Mk2)314
443179 Operating Panel Dimensions (Mk2)315
439594 Operating Panel Adapter Plate (Mk2)318

Kongsberg Simrad SY50 - Installation Manual

Table of Contents

Other manuals for Kongsberg Simrad SY50