As soon as the appliance reachesthe
appropriate temperature, the temperature
control indicator light (c) will come on.
.Then turn the function selector (b) to the
position «\!!\.J» untilthe milkisfrothed
enough, then reset it to the pOSItion 0 and
remove the container.
.Do the cleaning operation In order to
prevent the nozzle from becoming blocked:
place an empty container under the nozzle.
. then turn the function selector (b) to .the
position «\!!\.J»again during few seconds.
. turnthefunctionselector(b)to the position
O.
clean the nozzle with a damp cloth.
.For thorough cleaning of the nozzle, please
refer to the paragraph «Maintenance».
. Heating water (for tea, for example) or
thick liquids (soup, for example)
Please note: the sliding part (g2) of the
nozzle must be in the raised position (5).
.Fillthe water container with fresh, cold
water (1)
.Set the «on/off» switch (h) The indicator
light (h 1) comes on.
.Move the nozzle towards the outside of the
appliance.
As soon as the appliance reaches the
appropriate temperature, the temperature
control indicator light (c)willcome on.
.Place an empty container under the nozzle.
Return the nozzle to the Inside and hold the
container by its handle or place it on the grid
(i) (6)
.Then turn the function selector (b) to the
position«\!!\.J»untilto obtainsomesteam
then reset it to the position 0 and remove
the container
.Immerse the tip of the nozzle in the liquid to
be heated. Returnthe nozzleto the inside
and hold the container by Itshandle or place
It on the grid (i) (6)
As soon as the appliance reaches the
appropriate temperature, the temperature
control indicator light (c)willcome on.
.Then turn the function selector (b) to the
position «\!!\.J» until the liquid IShot enough,
then reset it to the position 0 and remove
the container.
10 KRUPS
.Forliquidsother than water, do the cleaning
operation inorder to prevent the nozzle
from becoming blocked:
place an empty container under the nozzle.
. then turn the function selector (b) to the
position «\!!\.J»again during few seconds.
. turn the function selector (b)to the position
O.
. clean the nozzle with a damp cloth.
.For thorough cleaning of the nozzle, please
refer to the paragraph «Maintenance».
Notes
Ifyou wish to make an espresso
immediately after steam, the appliance
must firstcool down until it reaches the right
temperature for extraction
.To do this, insert an empty filter holder (no
coffee) in the machine and pOSItion a
suitable container beneath it. Then turn the
function selector (b) to the position «~».
.Let the water run through until the indicator
light (c)goes out. Then, turn the function
selector (b)to the position 0
After this, the machine is now ready once
more to make an espresso (see paragraph
«espresso function»).
Please note: when the appliance is running,
and also afterwards, the nozzle willbe very
hot. Allowtime for the appliance to cool
down to prevent scalding or burning.
Maintenance
.Unplug the appliance and allow it to cool.
.Neverwash the accessoriesfor your espresso
In the dishwasher.
.Clean the body of the appliance with a
damp cloth.
After use, the water tank must be emptied.
. The drip tray (j)
.Each time an espresso is prepared, the drip
tray fills with water. This is perfectly normal.
To prevent any overflow, remove the grid (7)
and empty the drip tray regularly.
.If necessary, clean the dnp tray and the gnd
with water and a little non-abrasive
washing-up liquid,rinse and dry.When
replacing, return the plasticblock situated at
the back of the tray (8)
To Next Page
Loading...
Need help?
General
