To Next PageTo Next Page
Need help?Do you have a question about the Kubota 3220 and is the answer not in the manual?
General| Brand | Kubota |
|---|---|
| Model | 3220 |
| Category | Laboratory Equipment |
| Language | English |
Explains the meaning of indication marks like WARNING and CAUTION.
Defines various pictorial symbols used in the manual for safety.
Lists conditions for non-warranty and liability.
Covers load, parts, proximity, sterilization, grounding, and speed limits.
Covers explosion proofing, hazardous materials, lid/rotor safety.
Covers rotor condition, installation clearance, and ground cable.
Covers installation location, temperature, humidity, ventilation.
Covers lid closing, cleaning agents, caution plates, rotor fastening.
Recommends proof containers for toxic/radioactive samples.
Guides on tube types, sample balance, glass tubes, and cushions.
Compares rotor energy to automobile collision energy.
Lists usable rotors as of June 2021.
Explains rotor cycle limits and replacement intervals.
Recommends rotor replacement after 7 years and resin parts replacement.
Identifies main external parts of the centrifuge.
Describes buttons, displays, and lamps on the control panel.
Guides on unpacking and checking for damage and accessories.
Lists accessories for the HT/15 Rotor.
Lists accessories for HT and HT/2 Rotors.
Provides instructions for mounting the rotor onto the drive shaft.
Specifies clearance, surface, temperature, and ventilation for installation.
Details precautions for moving the centrifuge, including rotor removal and lifting.
Outlines required voltage, current capacity, and grounding for the power supply.
Explains ground wire connection and lists places to avoid.
Highlights key precautions from General Notes.
Outlines the fundamental sequence of operations.
Describes monitoring, halting, and post-operation steps.
Guides on reusing the centrifuge and powering it off, including parameter memorization.
Details turning on power and opening the centrifuge lid.
Explains emergency lid opening and safe closing procedures.
Describes how to set the desired rotational speed.
Explains how to set the HT/15 rotor for Hematocrit or 15mL tubes.
Details setting operation time in minutes, seconds, or hold.
Explains continuous run by holding the START key.
Describes saving, recalling, and cancelling stored parameters.
Covers setting deceleration, sounds, buzzer, and reminder alarms.
Details setting the starting speed for natural deceleration.
Explains selecting end-of-operation sounds or silence.
Describes enabling or disabling the buzzer for alerts.
Explains activating or deactivating the alarm for samples left in the centrifuge.
Provides formula and guidance for calculating centrifugal force.
Explains calculating reduced maximum speed based on load and specific gravity.
Lists daily checks for rotor, chamber, grounding, and controls.
Details monthly checks for rotor appearance, damage, and cleaning.
Lists items for annual inspection requiring dealer service.
Provides instructions for cleaning the chamber to prevent rust.
Guides on cleaning rotors/tubes and cautions against high-temperature sterilization.
Explains how to check and reset the circuit protector.
Details the lifespan and replacement method for capillary tube protective packing.
Explains how to use the tachometer port for rotation measurement.
Informs about spare parts availability period after discontinuation.
Outlines necessary information and preparation for repair submissions.
Specifies required information and certificate for handling biohazards during service.
Details contaminant removal and certificate attachment before returning equipment.
Explains how alarms are indicated and lists specific alarm codes (E0, C1-C5).
Describes how errors are indicated and lists specific error codes (E1-E9).
Provides a table of common problems, checkpoints, and actions.
Addresses issues like excessive vibration, abnormal noise, and incorrect speed indication.
Covers specifications, usage, and component handling for the HT/15 Rotor.
Lists specifications for the HT rotor and explains its use for Hematocrit capillary tubes.
Explains how to correctly set capillary tubes in the HT rotor.
Explains how to set 15mL metal tubes in the HT/15 rotor.
Warns about glass tube strength and proper use of cushions.
Details cushion specifications and placement/removal methods.
Details specifications for the HT rotor and provides a Speed-RCF table.
Explains preparation and setting of capillary tubes in the HT rotor.
Emphasizes symmetrical distribution of capillary tubes for safe operation.
Details specifications for the HT/2 rotor, including various tube types.
Explains setting capillary tubes in the HT/2 rotor.
Guides on micro tube distribution and warns against rotor decomposition/repair.
Explains reading Hematocrit values using the measuring plate.
Provides a comprehensive list of the centrifuge's technical specifications.
Lists available rotor and adaptor models with code numbers.
Lists various spare parts and components with code numbers.
Guides on disposal and notifying about contaminants.
Explains how to use the nomograph for calculation.
