Need help?Do you have a question about the KUHL FC 303 GC and is the answer not in the manual?
Discusses general safety measures and accident prevention relevant to dealers.
Explains the meaning of the warning symbol used throughout the manual.
Advises on wearing appropriate personal protective equipment and clothing.
Specifies criteria for lifting devices such as hoists and forklifts.
Directs users to consult the operator's manual for safe machine operation.
Details technical specifications for the FC303GC mower conditioner model.
Lists optional equipment kits available for the machines.
Outlines the necessary tractor power and hydraulic requirements.
Details technical specifications for FC 353 GC and FC 353 RGC mower conditioner models.
Describes initial machine packaging and procedures for separating pallets.
Provides advice on fork separation distance for safe forklift operation.
Instructs on correct sling placement for lifting with a hook.
Instructions for placing the pallet on flat ground and checking tension hoops.
Details steps to cut tension hoops and remove swath boards and rear hoods.
Instructions for removing the right and left front plates of the machine.
Instruction to remove the box containing unassembled parts.
Instructions to cut tension hoops and remove side gearbox cover and rear guards.
Instructions for removing the front panel using lifting equipment.
Instructions for removing central support screws and drawbar tension hoops.
Instruction to remove the wooden plate from the Gyrodine headstock yoke.
Instructions for removing and reinstalling tubular support screws.
Instruction to place the drawbar using a hoist next to other parts.
Instructions to cut tension hoops and remove primary PTO shaft, third PTO shaft, and parking stand.
Instructions for installing wheels on machines that were palleted without them.
Details sling placement and tensioning for lifting the machine with a hook.
Safety measures and procedures for tipping the machine assembly using a hook.
Instructions for using wheel wedges and placing support wedges for the cutterbar.
Procedure for adjusting sling length by doubling it for re-attachment.
Instructions for driving forklift forks and securing the cutterbar with a sling.
Procedures for lowering the machine onto support wedges using a forklift.
Instructions for mooring the pallet and removing securing screws and supports.
Procedures for removing/reinstalling the pivot pin, engaging the drawbar, and routing hoses.
Instructions for removing packing support, fitting the parking stand, and resting the drawbar.
Steps for pivoting the drawbar and installing the intermediate PTO assembly.
Instructions for securing the PTO yoke and installing the inspection cover.
Instructions for securing the PTO housing and mounting the safety guard.
Instructions for mounting the PTO swivel rod and removing the guard cone.
Instructions for installing the primary PTO yoke and connecting electrical/hydraulic lines.
Steps for attaching conditioning unit, removing/installing brackets, and adjustment rod.
Instructions for tightening wheel bolts and checking tire pressure for specific machines.
Instructions for installing the suspension adjustment crank and fitting the PTO shaft.
Instructions for fitting bellows and reinstalling the right side guard.
Instruction for fixing the tank to its holder using screws, washers, and nuts.
Instructions for fitting the left side guard and deflectors.
Instruction to remove the central support bracket and mount the skid.
Instructions for placing front panel, installing shields, and securing them.
Instructions for mounting the left front signalling panel and light.
Instructions for mounting the hood and placing the belt guard.
Instructions for mounting the right front signalling panel and light.
Instructions for assembling swath boards and rear swathing hooding.
Steps for mounting swath board locking handles in the correct order.
Instructions for fitting the rear safety curtain and rear shields.
Instructions for mounting wheel wedge holders onto the frame supports.
Instructions for installing rear signalling panel mounting plates.
Instructions for fitting rear right and left signalling panels and lights.
Instructions for installing lighting elements specific to the U.S. and Canada.
Instructions for installing the SMV bracket.
Instructions for applying red reflectors on the rear shields.
Instruction for applying an amber reflector on the side gearbox shield.
Instructions for applying amber reflectors on the side shields.
Guidance on correct decal placement and applying French language decals for Canada.
Provides an example for translating English decals to French.
Explains caution decals related to manual reading and machine maintenance.
Explains warning decals for maneuvering hazards and rotating parts.
Explains warning decals for guards and caution for genuine parts.
General| Brand | KUHL |
|---|---|
| Model | FC 303 GC |
| Category | Farm Equipment |
| Language | English |
To Next Page
