KUNTENG KT-LCD8S User Manual

KT-LCD8S E-Bike Display User Manual
Dear customer, please read this manual before you use KT-LCD8S Display. The manual will guide you use the instrument
correctly to achieve a variety of vehicle control and vehicle status displays.
Functions and Display
Instruments using the structure form of instrument body portion and the operation buttons are
designed separately.
1
UP Button
9
VOL
Battery voltage
2
SW Button
10
The brake display
3
DOWN Button
11
Backlight and headlights
4
ASSIST
Pas level
12
℃
Environment temperature
6Km/H push power assist
℉
Environment fahrenheit
5
THROTTLE
Run sign
13
MOTOR W
Power display
6
Km/H
Riding speed(metric)
14
DST
Trip distance
7
AVS
Average speed
ODO
Total distance
MXS
MAX speed
15
TIM
Single trip time
8
Battery capacity indicator
TTM
Total trip time
1. Operation
1. ON/OFF
Hold button long to turn on the power, and hold long for a second time to turn off
the power. When the motor stops driving and when the e-bike is not used for a consecutive 5
minutes, it will automatically shut down and turn off the motor power supply.
2. Display 1
Hold button to start up and enter display .
2.1 Turn on backlight and headlights
Hold long to turn on backlight and headlights (the controller
should have headlight drive output function); hold long again to
turn off the backlight and headlights.
2.2 Assist ratio gear (ASSIST) switch
Press or to switch 1-5 file gear. Gear 1 is for the
minimum power, gear 5 is for the highest power. Each startup will
automatically restore the gear shutdown last time (the user can set
randomly). Gear 0 is without booster function.
2.3 6Km/H assist promotion function
Hold and flashes, the vehicle drives at the speed not more
than 6Km /h. Release button, the function is invalid.
2.4 Display and delete of single data
After power on for 5 seconds, hold and at the same
time, single trip riding time (TM) and single trip distance (DST) flash,
hold button shortly, the content of both is cleared. If failed
holding the button within 5 seconds, it will automatically return the
display interface after 5 seconds, original content is preserved.
3.Display 2
Hold button shortly in display 1 to enter display 2.

KUNTENG KT-LCD8S Specifications

General

Display Type	LCD
Backlight	Yes
Voltage	24V/36V/48V
Waterproof Rating	IP65
Handlebar size for Holding	22.2 mm
Compatibility	Kunteng KT series controllers
Connector	5-pin

Summary

Functions and Display Overview

Button Functions

Description of UP, SW, and DOWN button functions.

Assist and Speed Functions

Description of ASSIST, 6Km/H assist, and speed displays.

Indicator Displays

Description of throttle, battery, motor, and trip data displays.

Environmental and Lighting Controls

Description of temperature, backlight, and headlight controls.

E-Bike Display Operation

Power On/Off

Instructions for turning the e-bike display and motor on and off.

Display Modes and Features

Details on cycling through display modes and activating features.

Backlight and Headlight Control

How to turn on and off the backlight and headlights.

Assist Ratio Gear Selection

How to switch between assist gears 1-5 for power.

6Km/H Assist Promotion

How to activate the 6Km/H push power assist function.

Data Display and Deletion

How to display and clear single trip data (TM and DST).

Advanced Display Navigation and Settings

Display Mode Switching

Instructions for switching between display modes 1, 2, and 3.

Error Code Display

Explanation of error codes and their definitions.

General Project Settings

Configuration settings for maximum speed, wheel diameter, and units.

Metric Unit Settings

How to set speed, mileage, and ambient temperature units.

Outline Drawings and Dimensions

Instrument Body Dimensions

Physical dimensions of the main instrument body.

Mounting Dimensions

Dimensions for mounting the double brackets.

Button Box Dimensions

Physical dimensions of the button control box.

Wiring Diagram

Diagram illustrating the wiring connections for the display system.