Kyosho KT-19 - User Manual

To Next Page



TRANSMITTER KT-19

产品介绍 Introduction

KT-19 遥控系统主要是用来遥控摩托车模型，通过对发射机进行操作，可以分别

实现相对应的马达驱动及舵机摆动遥控控制；发射机采用 6V/DC 供电，摩托车采用

3.7V 锂聚合物电池进行供电。

KT-19 radio system mainly uses for remote control the motorcycle model.

Through operating transmitter, it can succeed in moving the motor system and the

servo respectively. The transmitter will be supplied by 6V/DC, while the receiver will

be supplied by 3.7V li-poly battery.

产品套装：发射机+摩托车（接收机）+USB 线+充电器+使用说明书。

Product includes: transmitter + motor (receiver)+USB cable + charger + manual

KT-19 遥控系统使用方法及操作步骤

Instruction of KT-19

1. 将发射机与摩托车（接收机）靠近；

1. Keep the transmitter and model closer.

2. 将发射机手轮顺时针拧到底，然后按下电源开关“POWER”，此时发射机 LED 指示

灯会处于闪烁状态；

2. Turning the steering wheel to the end clockwise, and at the same time press the

POWER, then the LED will be flashing.

3. 打开接收机电源开关，接收机 LED 指示灯会长亮 2 秒时间，然后处于闪烁状态，

同时，无刷电机也会发出“滴、滴、滴”的响声；

3. Switch on the power of receiver, then the LED of receiver will be lighting for 2

seconds, after that it will be flashing, and at the same time the brushless motor will

be beeping.

Main Page

Need help?

Do you have a question about the Kyosho KT-19 and is the answer not in the manual?

Overview

Transmitter KT-19

Transmitter KT-19

Function Description

The KT-19 radio system is primarily designed for remote control of motorcycle models. By operating the transmitter, users can control the motor drive and servo movement of the motorcycle. The transmitter is powered by 6V/DC, while the receiver (within the motorcycle) is powered by a 3.7V Li-poly battery.

The product package includes:

Transmitter
Motor (receiver)
USB cable
Charger
User manual

Important Technical Specifications

Transmitter:

Operating Frequency: 2405.5MHz - 2475MHz
Quiescent Current: Approximately 17mA
Effective Remote Control Distance: 30 meters
Compliance: Conforms to CE and FCC requirements
Weight: 280g
Dimensions (Length x Width x Height): 162 x 71 x 295mm
Input Voltage: 4.8V-6VDC
Output Power: 4.8V-6VDC
Battery Type: 4 x AAA/1.5V dry batteries

Motorcycle (Receiver):

Dimensions (Length x Width x Height): 116 x 70 x 70mm
Battery Type: 3.7V Li-poly battery
Low Voltage Alarm: 3V (for the receiver)

Usage Features

Instruction of KT-19:

Proximity: Keep the transmitter and the motorcycle model closer to each other.
Transmitter Power On: Turn the steering wheel clockwise to its end, then press the "POWER" button. The transmitter's LED indicator will start flashing.
Receiver Power On: Switch on the power of the receiver. The receiver's LED indicator will light up for 2 seconds, then start flashing. Simultaneously, the brushless motor will emit a "drip, drip, drip" sound.
System Activation: Switch on the transmitter's power button once more. Both the transmitter and receiver LEDs will remain constantly lit. The brushless motor will beep 15 times, after which the motor of the gyro will begin to move.
Operation: After approximately 5 seconds, the operating speed will stabilize. You can then adjust the steering direction and speed of the motorcycle by using the trim of the steering wheel, trigger, and gyro.

Battery Instructions:

Transmitter Battery: The transmitter is powered by 4 AAA/1.5V dry batteries. The input voltage is 4.8V-6VDC. When the transmitter is switched on, the green LED indicator will be constantly lit. If the battery voltage drops below 4.2V, the LED will flash, indicating that the batteries need to be replaced.
Receiver Battery: The motorcycle model uses a 3.7V Li-poly battery and a brushless motor system. The receiver has a low voltage alarm that triggers when the voltage is less than 3V.

3.7V Li-poly Battery Charging:

Charging Status: When the lithium battery is charging or not yet fully charged, the charger's LED indicator will be red.
Full/No Battery: When the LED indicator is green, it means the lithium battery is either fully charged or not connected.

Transmitter External Features (Numbered Diagram):

Antenna
LED Transparent Cover
USB Port
Battery Box Switch
Rubber Grip
Battery Box
Steering Wheel
Trigger
Steering Trim
Gyro LO SPEED Trim (low speed)
Gyro HI SPEED Trim (high speed)
POWER ON/OFF

Maintenance Features

Notes:

Manual Reading: This remote control model incorporates several high technologies and has a complex design and manufacturing process. Please read the "KT-19 User Manual" carefully before use to understand the operating techniques and safety rules.
Motor Safety: Do not touch the motor before it stops moving.
Pre-use Check: Before each use, double-check that the motorcycle model and remote control system are functioning correctly.
Obstacle Avoidance: When using the model, keep it away from obstacles. The motorcycle model is compact, and the receiver's antenna is close to the ground. If there are obstacles between the transmitter and the model, the remote control signal can easily be lost, leading to loss of control.
Heat Source Avoidance: The transmitter and the body of the motorcycle model are made of plastic. Avoid high temperatures to prevent plastic aging and deformation.
Humidity Avoidance: The transmitter and receiver contain many precise electronic components. Prevent moisture or water vapor from directly entering to avoid various circuit failures.

FCC Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Caution!

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.