KZN Solar GT-SKR010B User Manual (English)

Questions and Answers:

M
Matthew TranAug 20, 2025
Why doesn't my KZN Solar Heat Pump compressor work?
- M
  Matthew MartinezAug 20, 2025
  If the KZN Solar Heat Pump compressor isn't working, several factors could be at play. First, check for a power failure and resolve any issues with the power source. A destroyed compressor contactor, poor connection, or overheating protection could also be the cause; in these cases, replace the contactor or check and renovate the connection. Additionally, ensure that the water outlet temperature is properly set and that there is adequate water-flow by cleaning the water filter and removing any air in the water system.
T
Tonya HopkinsAug 22, 2025
How to fix low heating capacity in KZN Solar Heat Pump?
- A
  Adam LawsonAug 22, 2025
  If your KZN Solar Heat Pump has low heating capacity, start by checking for inadequate refrigerant and look for any leaks, refilling to the standard quantity if needed. Ensure proper heat insulation of the water system and replace the drying filter if it's stopped up. Also, clean the heat exchanger if the air side is inefficient and ensure adequate water-flow by cleaning the water filter.
C
Chelsea StanleyAug 25, 2025
What to do if my KZN Solar Heat Pump unit doesn’t work?
- N
  nicole94Aug 25, 2025
  If your KZN Solar Heat Pump unit isn't working, begin by checking for a power failure and ensuring the switch is off while you inspect the power source. Also, verify the power connection is secure and in good condition; renovate any bad connections. Lastly, inspect the fuse and replace it if it has blown.
K
Kristi AustinAug 26, 2025
Why is my KZN Solar Heat Pump compressor so noisy?
- B
  Brandon TranAug 26, 2025
  If the KZN Solar Heat Pump compressor is working but is excessively noisy, it could be due to liquid refrigerant entering the compressor, in which case you should check the expansion valve. Alternatively, the interior components may be damaged, requiring compressor replacement. It may also be caused by inadequate refrigeration oil, so add the correct amount of refrigeration oil.
A
April WilliamsAug 27, 2025
What causes hydraulic pressure switch protection interrupts in KZN Solar Heat Pump?
- F
  Fred GomezAug 27, 2025
  If the KZN Solar Heat Pump is experiencing hydraulic pressure switch protection interrupts, it could be due to several reasons. The hydraulic switch might be destroyed, requiring replacement. Inadequate water-flow could be the issue, so clean the wye strainer and increase water-flow. Air in the circulating water inlet tube can also cause this, so discharge the air. Additionally, check the circulating pump and capacitor for damage and repair if necessary. Finally, ensure the water tank is full and the water pressure exceeds 0.15Mpa.
D
David PriceAug 29, 2025
What causes high pressure switch fault in KZN Solar Heat Pump?
- T
  Todd SpenceAug 29, 2025
  If the KZN Solar Heat Pump is experiencing a high pressure switch fault that causes interrupts, it could be due to several reasons. The high pressure switch may be damaged and need replacement. Inadequate water-flow can cause this, so increase the flow. The system may be jammed, or the sensor probe may have fallen; check, clean the system, and retighten the probe. Also, check and repair the circulating pump and capacitor if they are damaged. Excessive refrigerant or un-condensable gas in the refrigerant system can also trigger this fault; drain out the extra refrigerant or gas.
K
Kelly TurnerAug 31, 2025
What to do for low water-flow protection in KZN Solar Heat Pump?
- S
  Sabrina StewartAug 31, 2025
  If the KZN Solar Heat Pump is experiencing low water-flow protection, it could be due to a destroyed hydraulic switch, which would need replacing. Alternatively, it may be caused by inadequate water-flow, so clean the filter and discharge any air.
R
Richard HarrisSep 2, 2025
What causes current protection in KZN Solar Heat Pump?
- B
  Brian GarciaSep 2, 2025
  If the KZN Solar Heat Pump is showing a current protection error, it is likely due to over-current. To resolve this, check the power supply.
A
Amanda WilkinsonSep 4, 2025
How to troubleshoot low pressure switch fault in KZN Solar Heat Pump?
- B
  Benjamin AllenSep 4, 2025
  If the KZN Solar Heat Pump is experiencing low pressure switch fault interrupts, first check if the low pressure switch is destroyed, and replace it if necessary. Also, check for inadequate refrigerant; perform leak hunting and refill to the standard quantity. Lastly, inspect the evaporator fins for dirt and clean them if needed.
M
Maria AlvaradoSep 5, 2025
Why is my KZN Solar Heat Pump compressor working but not heating?
- F
  floresericSep 5, 2025
  If the KZN Solar Heat Pump compressor is working but not heating, it could be due to refrigerant leakage, in which case you should perform leak hunting and refill with the standard quantity of refrigerant. Alternatively, the compressor itself may be faulty and require replacement.

KZN Solar GT-SKR010B Specifications

General

Model	GT-SKR010B
Category	Heat Pump
Brand	KZN Solar
Heating Capacity	10kW
Refrigerant	R410A
Power Source	Electrical
Power Supply	220-240V, 50Hz

KZN Solar GT-SKR010B User Manual

Table of Contents

Questions and Answers:

KZN Solar GT-SKR010B Specifications