To Next PageTo Next Page
Need help?Do you have a question about the L.B. White Tradesman CP170 and is the answer not in the manual?
Proper gas pressure is critical to prevent fires, explosions, and improper combustion.
Not for home/recreational use; installation may cause fire or explosion.
Keep combustibles away; avoid volatile materials; follow instructions to prevent fire.
Do not store flammable liquids nearby; actions to take if gas smell is detected.
Direct-fired heaters can expose users to hazardous CO, CO2, and NO2 levels.
Lists symptoms like headaches, dizziness, and difficulty breathing.
Fuel gas has added odorants; smelling gas is a signal for immediate action.
Discusses factors affecting odor perception and the importance of sensitivity.
Recognize gas odors and perform periodic sniff tests for safety.
Emphasizes that only qualified personnel should install, repair, or service the heater.
Installation must meet codes; adequate ventilation is required for combustion.
Avoid touching hot surfaces; keep away from propane containers; cleaning instructions.
Never bypass safety features; do not block air intakes/outlets.
Daily hose inspection and regular gas leak checks are crucial.
Use grounded receptacles; disconnect supply for storage.
Turn off gas supply and perform leak tests before starting installation.
Install on level surface respecting distances; secure LP containers.
Install indoors, protect from water, and maintain clearance from combustibles.
Ensure all gas leaks are identified and repaired before proceeding.
Qualified service must check operating gas pressure and regulator.
Use appropriate pipe thread compound; light according to manual instructions.
Understand operation, know how to shut off gas supply, and address defects.
Ensure adequate ventilation per OSHA and other codes for indoor use.
Vaporization depends on container area, fuel level, temperature, and humidity.
Provides tables for recommended number of gas cylinders based on temperature.
Details propane supply tank sizes and heaters per tank for CP400 models.
Instructions for attaching the handle securely to the heater barrel.
Steps for assembling the hose and regulator for the Tradesman 170 Propane.
Steps for assembling the hose and regulator for the Tradesman 400 LP.
Instructions for connecting the regulator for Tradesman 170 Natural Gas.
Assembly and connection steps for the Tradesman 400 Dual Fuel model.
Procedures for connecting natural gas supply with appropriate pressure.
Detailed steps for connecting the propane regulator to the fuel container.
How to adjust the heater's discharge outlet height for better heat direction.
Steps for startup, shutdown, and using selector/variable rate valves.
Essential cleaning steps and warnings to prevent component failure or damage.
Checks for clear surroundings, gas connections, regulator vent, wiring, and hose.
Annual checks of igniter, regulators, and auto reset high limit switches.
Warnings about hot surfaces after shutdown and fire/explosion hazards during service.
Procedures for removing panels to access electrical components and motor/fan assembly.
Instructions for removing, inspecting, and reinstalling motor, fan, and air proving switch.
Explains the function of high limit switches and their locations on different models.
Annual testing procedure for auto reset high limit switches using flame.
How to disconnect and replace the igniter for different models.
Steps for removing and accessing the thermostat bulb on different models.
Instructions for disconnecting and replacing the ignition control module.
Required tools and initial steps before measuring gas pressure.
How to install the pressure gauge on the gas control valve.
How to read the gauge and compare it to dataplate specifications.
Procedures for adjusting pressure, disconnecting, and final checks.
Lists the necessary tools for removing and cleaning the burner orifice.
Step-by-step guide on how to remove, clean, and reinstall the burner orifice.
Lists essential test equipment and explains the heater's sequence of operation.
Covers diagnostic codes for Ultra models and issues for non-diagnostic models.
Describes the process of ignition failure and safety lockout.
How to reset the system after an ignition failure lockout occurs.
Steps to check if the fan motor runs and the heater lights.
Checking LED status and thermostat voltage for proper operation.
Verifying power supply voltage to the heater and ignition control.
Diagnosing issues related to the air proving switch contacts.
Checking for and resolving binding issues with the air proving switch.
Checking for air inlet blockages and fan motor issues.
Verifying voltage to the ignition control and motor.
Checking switches for binding and continuity.
Addressing ignition failure and safety lockout indicated by three flashes.
Troubleshooting control module faults and power quality issues.
Diagnosing issues related to flame sensing, igniter, or ground.
Verifying power supply to heater and thermostat for proper operation.
Checking voltage from thermostat to ignition control and to the motor.
Diagnosing motor start issues and air proving switch contacts.
Ensuring fuel supply valves are open and gas pressure is correct.
Checking air proving switch and gas selector valve positions for correct function.
Diagnosing igniter spark, gap, and voltage supply to the gas valve.
Checking heater grounding, fuel supply, and gas pressure.
Verifying voltage supply and checking the igniter's condition (cleanliness, cracks).
Inspecting the high voltage lead connection and diagnosing the ignition control.
Wiring diagram showing electrical connections for the 170 Standard model.
Ladder diagram illustrating the electrical control logic for the 170 Standard model.
Wiring diagram for 170 Ultra and all 400 series heaters.
Ladder diagram for 170 Ultra and all 400 series heaters.
Visual identification of component parts for 170 and 170 Ultra models.
Detailed list of component parts with their corresponding numbers for 170/170 Ultra.
Visual identification of component parts for CP400, CP400-LP/Ultra models.
Detailed list of component parts with their corresponding numbers for 400 series.
Details warranty for heater components against defects in material and workmanship.
Warranty terms for replacement parts purchased from the company.
Information on contacting for service, registration, and warranty claims.
General| Brand | L.B. White |
|---|---|
| Model | Tradesman CP170 |
| Category | Heater |
| Language | English |
