What to do if the touchscreen on the LABORIE Aquarius XT tower is frozen?
If the touchscreen on the LABORIE Outdoor Cart tower is frozen, it might need a reset. To reset the system, press the reset button on the Central Hub Computer (CHC) for 5 seconds.
General| Brand | LABORIE |
|---|---|
| Model | Aquarius XT |
| Category | Outdoor Cart |
| Language | English |
Provides information on previous versions of the Aquarius system, specifically regarding button color changes.
Details the power requirements and specifications for various AQUARIUS® cart models including dimensions and operating conditions.
Lists the components and part numbers for different AQUARIUS® systems (LT, CT, XT, CTS) and software components.
Provides step-by-step instructions for setting up the AQUARIUS system, including cart setup and wheel locking.
Instructions on how to use the AQUARIUS system's lockable caster wheels for stability during testing procedures.
Instructions for connecting and setting up the optional bubble detector with the Central Hub Computer (CHC) for detecting air bubbles.
Step-by-step guide for assembling the optional UPP Puller Stand using provided hardware and tools.
Instructions for setting up the Uroflow Transducer (Urocap V or Spinning Disk) with the commode chair, funnel, and beaker.
Steps for setting up fluid-filled pressure transducers, including attaching cartridges, tubing, and flushing with fluid.
Detailed procedure for priming fluid-filled pressure transducers, tubing, and catheters to remove air bubbles.
Instructions for setting up dual and triple-lumen catheters for bladder and urethral pressure measurements.
Explanation of the Bluetooth and Equipment Status indicators on the Pump Hub, including the Stop button functionality.
Details on the message screens of the Roam DX, including pressure sensor port status and port connection information.
Step-by-step guide to calibrate the Urocap V for flow and volume measurements using the AQUARIUS software.
Procedure for calibrating pressure transducers using the Roam DX and AQUARIUS software, including zeroing and low load settings.
Explanation of the symbol indicating system and software connectivity and where to find system messages in the software title bar.
Overview of common system status messages displayed on the CHC touchscreen for various device modules.
Guidelines for general cleaning of the non-immersible AQUARIUS system, emphasizing protective gloves and proper cleaning solutions.
Instructions for cleaning and maintaining the Roam DX, noting it is not immersible and recommending specific cleaning agents.
Procedure for cleaning the Urocap V Uroflowmeter to prevent urine contamination, advising against immersion in liquids.
Instructions for cleaning and disinfecting the UPP Mobile Clamp, including warnings about damaging procedures and approved disinfectants.
Instructions for charging the batteries of Urocap V and Roam DX devices, including charging times and recommended charge levels.
Procedure to check the flow and volume readings of the Urocap V Uroflowmeter against a known volume of water.
Procedure for checking the pump's volume measurement accuracy against a known volume, ensuring proper tubing is used.
Procedure for checking EMG response by performing arm movements and fist clenching, noting electrode replacement recommendations.
Procedure to check the infusion transducer by infusing a known volume of water and comparing it to the Uroflowmeter's volume reading.
Troubleshooting steps for devices that do not respond, covering power issues, connection problems, and software settings.
Steps to troubleshoot power issues with the computer or printer, checking electrical outlets, power cords, and connections.
Troubleshooting for a specific USB power issue where the battery LED is orange but there is no response from the device or keyboard.
Troubleshooting for inability to wake up the Roam DX via OK button or Bluetooth, possibly due to low battery or connection issues.
Troubleshooting for a device showing partial charge despite being fully charged, possibly related to battery calibration or charger connection.
Steps to resolve high or low EMG readings, including scale optimization, electrode adhesion, and electrode detachment.
Steps to resolve inability to connect via Bluetooth, including checking distance, barriers, and re-establishing connection.
Troubleshooting for initial Bluetooth connection failures, involving waking up devices and restarting the system.
Steps to resolve connection issues between the PC and touchscreen, involving disconnecting/reconnecting Bluetooth devices and restarting software.
Information on electronic emissions compliance for the AQUARIUS Urodynamic Analyzer System according to CISPR standards.
Details electromagnetic immunity compliance levels for electrostatic discharge, electrical fast transient, surge, voltage dips, and magnetic fields.
Information on RF communications immunity, including conducted and radiated RF test levels and recommended separation distances.
To Next Page
