Lakeland Mills CF1009 User Manual

CF1009 TETE-A-TETE PORCH SWING
Please check contents before assembly. If any items are missing or damaged, do not take the unit back to the
store. Call 1-800-427-5136 for customer service and we will save you time by correcting any problems directly
for you.
TETE-A-TETE PORCH SWING HARDWARE TETE-A-TETE PORCH SWING COMPONANTS
2 - Preassembled Seat Backs 2 - 45” Swing
Bars
Preassembled Swing Seat
2 - 24” Arms
2 - 12”
Arm Supports
2 - 21-1/2”Seat Ends
2 - 9-1/2” Front
Table Supports
Table Top
NOTE: Cracks or Checks in logs are part of the natural
beauty of cedar logs and should not be considered de-
fects.
Right Left
”
4 - 1/4” x 5”
Hex Washer
Head Screw*
18 - 2 1/2” Screws
2 - Barrel
Nuts
2 - 3/8”
Washers
2 - S Hooks 2 - 3/8” x 5” Eye Bolts
* Lag Screws and Washers may be substituted for Hex Washer
Head Screws
TOOLS REQUIRED
Tape
Measure
Pencil
Rubber Mallet or Block
of Wood & Hammer
#2 Phillips Screw-
driver & Regular
Screwdriver
7/16 Socket or Wrench
NOTE: Using a battery
Or electric power drill with a socket attachment will make
assembly easier and faster.
 Read all instructions before starting.
Helpful Tips:
 To start hex washer head screws, hammer into
wood about 1/2” then use wrench or socket to
tighten.
 Do not completely tighten any screws until the unit
is fully assembled and setting on a level surface.
 If you have hardware left over after completing
your unit, it most likely has been assembled incor-
rectly, and may not be safe to use. Please call
Customer Service at 1-800-427-5136, for assis-
tance.
 A battery operated or electric drill will make as-
sembly faster and easier.
 Use a good quality penetrating oil or wood deck
sealer with a UV inhibitor & an anti-fungal. (Make
sure product is intended for outdoor use.)
 If staining or finishing before assembling, tape off
all dowel ends. (Finishes will cause the dowels to
swell, making assembly difficult
 Check all nuts and bolts for tightness before
and during each usage season.
Figure 1
Install seat ends onto seat. Align holes in seat end with
dowels on seat . Repeat on other side. Secure with screws
perpendicular to dowel. IMPORTANT: The single hole
should be placed toward the front of the seat. (See right).
Figure 1. Secure with screws.
STEP 1
Please Note: After you have installed the seat ends onto the seat
secure with (4) 2 1/2” screws.

Lakeland Mills CF1009 Specifications

General

Brand	Lakeland Mills
Model	CF1009
Category	Outdoor Furnishing
Language	English

Summary

TETE-A-TETE PORCH SWING COMPONENTS

Preassembled Seat Backs

Includes left and right preassembled seat backs for the porch swing.

Table Top

Component for the table section of the porch swing.

Swing Bars

Two 45" swing bars used for attaching the swing.

Preassembled Swing Seat

The main seating component of the porch swing.

Front Table Supports

Two 9-1/2" supports for the table section.

Arms

Two 24" arms for the porch swing structure.

Seat Ends

Two 21-1/2" seat ends for the swing seat.

Arm Supports

Two 12" arm supports for the swing.

TETE-A-TETE PORCH SWING HARDWARE

Hex Washer Head Screws

Includes 4- 1/4" x 5" Hex Washer Head Screws.

S Hooks

Two S hooks for connecting swing components.

Eye Bolts

Two 3/8" x 5" Eye Bolts.

Barrel Nuts

Two barrel nuts for securing hardware.

Lag Screws

Eighteen 2-1/2" lag screws for assembly.

Washers

Two 3/8" washers for hardware.

TOOLS REQUIRED FOR ASSEMBLY

Hammer & Mallet

Rubber mallet or block of wood and hammer for assembly.

Wrench or Socket

7/16 socket or wrench for tightening screws.

Screwdriver

Phillips screwdriver for assembly.

Measuring Tools

Tape measure and pencil for marking and alignment.

Assembly Instructions

Step 1: Install Seat Ends

Attach seat ends to the seat using screws, aligning holes with dowels.

Step 2: Assemble Seat Backs

Lay seat on flat surface, insert uprights into seat rail holes.

Step 3: Attach Table Supports & Back

Insert table supports and attach rear table support to assembled back.

Step 4: Attach Arms

Insert arm supports into holes and fasten arms to frame with lag screws.

Step 5: Secure Dowel Joints

Secure all assembled dowel joints with screws.

Step 6: Attach Swing Bars

Attach swing bars to arms and seat ends using lag screws.

Lakeland Mills Recommendations

Wood Stain & Sealant

Recommendation for WeatherSeal Premium Oil-Based Exterior Wood Stain & Sealant.