Land Pride RCF3696 User Manual (English)

Questions and Answers:

M
mcarrAug 19, 2025
Why is my Land Pride Tractor Accessories driveline clutch slipping?
- C
  Christopher KennedyAug 19, 2025
  Your Land Pride Tractor Accessories driveline clutch might be slipping due to several reasons. It could be from scalping the ground, so try raising the cutting height. Another cause may be cutting too fast; reduce your travel speed. Engaging the power take-off too quickly at high engine rpm can also cause this issue, so engage it slowly at low engine rpm. Finally, avoid cutting over solid objects.
J
Joshua NelsonAug 21, 2025
Why are the blades breaking on my Land Pride Tractor Accessories?
- J
  Jeffery JordanAug 21, 2025
  The blades on your Land Pride Tractor Accessories might be breaking because you are hitting solid objects; try to avoid them. Another reason could be that the blades are hitting each other, in which case the blade carriers need to be timed.
P
Patricia HuffmanAug 23, 2025
What causes excessive vibration in Land Pride Tractor Accessories?
- E
  Emily GuerreroAug 25, 2025
  Excessive vibration in your Land Pride Tractor Accessories can stem from several issues. A bent driveline, loose blades, a bent blade carrier, or a broken blade could each be the cause, consider replacing these parts if damaged. Additionally, a blade that won't swing freely or blades with unequal weight can lead to vibration; inspect or replace the blades as needed.
T
Timothy CarterAug 26, 2025
What to do if Land Pride RCF3696 Tractor Accessories oil seal leaking?
- R
  Russell BrownAug 26, 2025
  If the oil seal on your Land Pride Tractor Accessories is leaking, it could be due to a few reasons. The gearbox might be overfilled, so drain it to the side plug hole. The seals could be damaged and need replacement. Also, check daily for grass or wire wrapped on the shaft in the seal area.
O
operezAug 28, 2025
Why is my Land Pride Tractor Accessories driveline yoke failing?
- B
  Benjamin KingAug 28, 2025
  The driveline yoke or cross on your Land Pride Tractor Accessories might be failing due to a shock load; avoid hitting solid objects. It could also be due to lack of lubrication; lubricate every 8 hours.
S
Stephanie NolanAug 30, 2025
Why are the blades wearing excessively on my Land Pride RCF3696?
- C
  Christie HudsonAug 30, 2025
  The blades on your Land Pride Tractor Accessories might be wearing excessively because you are cutting on sandy ground or contacting the ground frequently. In either case, try raising the cutting height.
J
Joseph MillerSep 1, 2025
What causes a Land Pride RCF3696 Tractor Accessories blade carrier to become loose?
- E
  Edward HernandezSep 2, 2025
  A Land Pride Tractor Accessories blade carrier might become loose if it has been running loose in the past, in which case you should replace the gearbox output shaft and blade carrier. It could also be that the blade carrier hardware is not tight enough; tighten it to the specified torque.
A
Amber GonzalezSep 4, 2025
What to do if Land Pride Tractor Accessories driveline telescoping tube failing?
- L
  Lindsay HessSep 4, 2025
  If the driveline telescoping tube on your Land Pride Tractor Accessories is failing, it is likely due to a shock load. Avoid hitting solid objects to prevent this.
A
Anthony AndersonSep 6, 2025
Why is the Land Pride RCF3696 driveline telescoping tube wearing?
- G
  Gail WardSep 6, 2025
  The driveline telescoping tube on your Land Pride Tractor Accessories might be wearing because it needs lubrication. Lubricate it every 20 hours.
C
carrierobbinsSep 9, 2025
What causes excessive side skid wear on Land Pride Tractor Accessories?
- D
  David CamposSep 9, 2025
  Excessive side skid wear on your Land Pride Tractor Accessories can be caused by a cutting height that is not level, soil that is abrasive, or cutting too low. Adjust the cutter height to resolve these issues.

Land Pride RCF3696 Specifications

General

Category	Rotary Cutter
Model	RCF3696
Working Width	96 inches
Cutting Width	96 inches
Number of Blades	2
Warranty	1 year limited
Cutting Height	1.5" - 12" (3.8 - 30.5 cm)
Deck Construction	10-gauge steel

Summary

Rotary Cutters Overview

3-Point Rotary Cutter Setup

Illustrates the 3-point mounted rotary cutter configuration.

Semi-Mount Rotary Cutter Setup

Illustrates the semi-mount rotary cutter configuration.

Pull-Type Rotary Cutter Setup

Illustrates the pull-type rotary cutter configuration.

Operator's Manual Information

Provides essential information about the operator's manual and safety.

Machine Identification and Dealer Information

Machine Identification Log

Section to record detailed information about the machine.

Dealer Contact Information

Fields for entering dealer contact details.

California Proposition 65 Warning

States warning regarding cancer and reproductive harm.

Important Safety Information

Safety at All Times

Emphasizes careful operation as best accident prevention.

Look for the Safety Alert Symbol

Explains the meaning and importance of the safety alert symbol.

Safety Precautions for Children

Highlights dangers and precautions when children are present.

Safety Information Continued

Use A Safety Chain

Guidance on using safety chains for towed implements.

Transport Safely

Rules and guidelines for safe transportation of equipment.

Tire Safety

Critical information and warnings regarding tire maintenance and changing.

Practice Safe Maintenance

Provides guidelines for performing maintenance safely.

Continued Safety Precautions

Prepare for Emergencies

Advises on preparedness for emergencies like fires and injuries.

Personal Protective Equipment and Fluid Hazards

Details PPE and warns about high-pressure hydraulic fluids.

Visibility and Operator Safety Features

Recommends safety devices and prohibits riders for enhanced safety.

Additional Safety Guidelines

Avoid Crystalline Silica Dust

Advises on precautions when working with crystalline silica dust.

Handle Chemicals Properly

Provides guidance on safe handling and storage of chemicals.

Dig Safe - Avoid Underground Utilities

Emphasizes contacting utility companies before digging.

Safety Labels and Hazards

Rotating Driveline Contact Hazard

Warns about severe injury or death from driveline contact.

Thrown Object and Rotating Blade Hazard

Alerts to hazards from thrown objects and rotating blades.

Crushing, Run Over, and Rollover Hazards

Covers hazards of crushing, being run over, and tractor rollovers.

Specific Safety Label Warnings

Guard Missing Hazard

Warns against operating with missing guards, causing entanglement.

Rotating Blades Hazard

Details hazards associated with rotating blades.

Thrown Object Hazard

Warns about hazards from thrown objects during operation.

Introduction to Your Rotary Cutter

Application Overview

Describes the intended applications and capabilities of the rotary cutters.

Using This Manual

Guides the user on how to effectively use the operator's manual.

Owner Assistance and Further Help

Provides information on obtaining assistance and contacting the service department.

Section 1: Assembly & Set-Up

Tractor Requirements

Outlines tractor specifications and horsepower needed for operation.

Dealer Preparations

Details essential pre-assembly checks and dealer responsibilities.

Pre-Assembly Checklist

Lists items to check before starting the assembly process.

Assembly Procedures

Gearbox Vent Plugs and Dipsticks

Instructions for installing vented dipsticks to replace solid plugs.

Tractor Shutdown Procedure

Step-by-step guide for safely shutting down the tractor.

Getting Started with Cutter Types

Introduces the three main cutter types: 3-point, Semi-Mount, and Pull-Type.

3-Point Hitch Assembly

3-Point Assembly and Set-Up

Detailed instructions for assembling the 3-point hitch system.

Hitch Assembly (3-Point)

Specific steps for assembling the hitch components for 3-point models.

3-Point Driveline and Hose Hook-up

Spring Hose Loop Assembly (3-Point)

Instructions for attaching the spring hose loop for 3-point hitches.

Driveline Installation (3-Point)

Steps for correctly installing the driveline on 3-point cutters.

3-Point Tailwheel Assembly

RCF(M)3696 Tailwheels (3-Point)

Instructions for installing tailwheels on RCF(M)3696 3-point models.

RCF(M)3610 3-Point Tailwheel Assembly

RCF(M)3610 Tailwheels (3-Point)

Instructions for installing tailwheels on RCF(M)3610 3-point models.

RCF(M)3696 3-Point Hitch Hook-Up

RCF(M)3696 Hitch Hook-Up (3-Point)

Guide for connecting the RCF(M)3696 cutter to a tractor hitch.

RCF(M)3610 3-Point Hitch Hook-Up

RCF(M)3610 Hitch Hook-Up (3-Point)

Guide for connecting the RCF(M)3610 cutter to a tractor hitch.

3-Point Driveline Hook-up

Driveline Hook-up (3-Point)

Steps for connecting the driveline for 3-point hitch operation.

3-Point Hydraulic and Hitch Pin

Hydraulic Hook-up Option (3-Point)

Instructions for connecting hydraulic hoses for 3-point cutters.

Hitch Pin Modification (3-Point & Semi)

Details modifications needed for specific hitch pin types.

Section 1: Assembly & Set-Up Continued

Semi-Mount Assembly and Set-Up

Instructions for assembling the semi-mount hitch system.

Spring Hose Loop Assembly (Semi-Mount)

Steps for attaching the spring hose loop for semi-mount hitches.

Driveline Installation (Semi-Mount)

Guide for installing the driveline on semi-mount cutters.

Semi-Mount Tailwheel Assembly

RCF(M)3696 Tailwheels (Semi-Mount)

Instructions for installing tailwheels on RCF(M)3696 semi-mount models.

RCF(M)3610 Semi-Mount Tailwheel Assembly

RCF(M)3610 Tailwheels (Semi-Mount)

Instructions for installing tailwheels on RCF(M)3610 semi-mount models.

Semi-Mount Hitch Hook-Up

Hitch Hook-Up (Semi-Mount)

Guide for connecting the semi-mount cutter to a tractor hitch.

Semi-Mount Driveline and Hydraulic Hook-up

Driveline Hook-up (Semi-Mount)

Steps for connecting the driveline for semi-mount hitch operation.

Hydraulic Hook-up (Semi-Mount)

Instructions for connecting hydraulic hoses for semi-mount cutters.

Driveline Checks and Assembly

Check Driveline Collapsible Length

Procedure to check driveline length to prevent damage.

Driveline Shortening

Steps for shortening the driveline if it's too long.

Assemble Inner & Outer Driveline Halves

Instructions for reassembling driveline components.

Driveline Clearance Check

Check Driveline Clearance

Ensures adequate clearance for driveline operation at various angles.

Pull-Type Hitch Assembly

Pull-Type Assembly and Set-Up

Instructions for assembling the pull-type hitch system.

Tailwheel Lift Options

Describes the available tailwheel lift mechanisms.

Axle Assembly (Pull-Type)

Steps for assembling the axle and associated components for pull-type units.

Pull-Type Components Assembly

Spring Hose Loop (Pull-Type)

Instructions for attaching the spring hose loop for pull-type hitches.

Tongue Assembly (Pull-Type)

Steps for assembling the tongue for pull-type cutters.

Park Jack Assembly (Pull-Type)

Instructions for installing and positioning the park jack.

Pull-Type Driveline Installation

Equal Angle Driveline (Pull-Type)

Installation guide for the equal angle driveline on pull-type cutters.

Constant Velocity Driveline Installation

Constant Velocity Driveline (Pull-Type)

Installation guide for the CV driveline on pull-type cutters.

Pull-Type Hitch Hook-Up

Hitch Hook-Up (Pull-Type)

Guide for connecting the pull-type cutter to a tractor hitch.

Pull-Type Hitch and Hydraulic Connections

LP Performance Hitch Hook-Up

Steps for connecting the LP Performance Hitch.

Safety Chain Hook-Up For Pull-Type

Guidance on attaching safety chains for pull-type implements.

Hydraulic Hook-Up (Pull-Type)

Instructions for connecting hydraulic hoses for pull-type cutters.

Purge Hydraulic System (Pull-Type)

Procedure to remove air from the hydraulic system.

Section 2: Assembly of Optional Equipment

Chain Safety Guards (Optional)

Instructions for installing chain safety guards for protection.

Rear Chain Guard

Guide for attaching the rear chain guard.

Front Chain Guards

Instructions for attaching the front chain guards.

Optional Safety Guard Installation

Rubber Safety Guards (Optional)

Instructions for installing rubber safety guards for protection.

Front Rubber Guards

Guide for attaching front rubber guards.

Rear Rubber Guard

Instructions for attaching the rear rubber guard.

Pull-Type Hitch Options and Changes

Pull-Type Hitch Options

Describes available hitch options for pull-type cutters.

Swivel Clevis Hitch

Details the features and hook-up of the swivel clevis hitch.

Land Pride Performance Hitch

Details the features of the LP Performance Hitch.

Change Out Hitches

Instructions for changing between different hitch types.

Check Chain Installation

Check Chains (Accessory)

Instructions for installing and adjusting check chains for height control.

Section 3: Adjustments

Park Jack Angle Alignment

Procedure to align the park jack vertically for proper support.

Deck Leveling and Height Adjustments

Deck Leveling and Height Adjustment

General guide for deck leveling and cutting height adjustments.

3-Point With Beam Arms

Specific adjustments for 3-point cutters with beam arms.

Level Left To Right

Steps to ensure the cutter deck is level side-to-side.

Cutting Height Adjustment

How to set the desired cutting height for optimal performance.

Further Deck Adjustments

Level Front To Back

Adjusting the cutter to be slightly lower at the front.

Center Link Adjustment

How to adjust the center link for proper hitch alignment.

Adjustments for Rear Axle Cutters

3-Point or Semi-Mount With Rear Axle

Adjustments for 3-point/semi-mount cutters with rear axles.

Level Left To Right

Steps to ensure the cutter deck is level side-to-side.

Cutting Height Adjustment

How to set the desired cutting height.

Leveling Pull-Type Cutters

Level Front To Back

Adjusting the cutter to be slightly lower at the front.

Pull-Type Rear Axle Adjustments

Pull-Type With Rear Axle

Adjustments for pull-type cutters with rear axles.

Level Front To Back

Adjusting the cutter to be slightly lower at the front.

Cutting Height Adjustment

How to set the desired cutting height.

Pull-Type Cutting Height Adjustment

Cutting Height Adjustment For Pull-Type

Specifics on adjusting cutting height for pull-type cutters.

Section 4: Operating Instructions

Operating Checklist

A list of pre-operation checks for safe use.

Safety Information

Crucial safety warnings and guidelines for operation.

Pre-Operation Inspections

Inspect Tractor & Cutter

Procedures for inspecting the tractor and cutter before and during operation.

Operating Procedures

Transporting

Guidelines for safely transporting the rotary cutter.

Blade Engagement and Disengagement

Procedures for safely starting and stopping the cutter blades.

Field Operation

Best practices for operating the rotary cutter in the field.

Navigating Terrain and Turns

Crossing Steep Ditches & Banks

Advice on safely navigating ditches and banks.

Turning Angles for Pull-Type Cutters

Information on permissible turning angles for pull-type cutters.

Unhooking 3-Point or Semi-Mount Cutters

Unhook 3-Point or Semi-Mount

Steps for safely detaching 3-point or semi-mount cutters.

Unhooking Pull-Type Cutters

Unhook Pull-Type

Steps for safely detaching pull-type cutters.

General Operating Instructions

Comprehensive guide to operating the rotary cutter safely and efficiently.

Section 5: Maintenance & Lubrication

Maintenance Overview

Emphasizes the importance of regular servicing for longevity.

Hydraulic System Care

Guidelines for maintaining the hydraulic system to prevent issues.

Tire Maintenance

Critical safety and maintenance procedures for tires.

Blade Maintenance Procedures

Cutter Blade Maintenance

Instructions for inspecting, sharpening, and replacing cutter blades.

Driveline and Clutch Maintenance

Driveline Slip-Clutch

Explains the function and maintenance of the driveline slip-clutch.

Clutch Run-In Procedure

Steps for running in the friction clutch before operation.

Slip Clutch Service

Clutch Disassembly

Steps for taking apart the slip-clutch assembly.

Clutch Inspection

Guidance on checking slip-clutch components for wear.

Clutch Assembly

Instructions for reassembling the slip-clutch.

Component Maintenance

Flex Couplers

Instructions for replacing flex coupler rubber discs.

Skid Shoe Maintenance

Guidelines for checking and replacing skid shoes.

Storage and Parts Ordering

Long-Term Storage

Procedures for preparing the implement for long-term storage.

Ordering Replacement Parts

Information on how to order replacement parts, including color codes.

Lubrication Points Guide

Lubrication Points

Identifies all lubrication points and their required intervals.

Gearbox and Coupler Lubrication

Gearbox Lubrication

Procedures for checking and filling gearbox oil levels.

T-Gearbox Lubrication

Procedures for checking and filling T-gearbox oil levels.

RCF(M)3610 Flex Coupler Lubrication

Lubrication details for the RCF(M)3610 flex coupler.

Driveline Lubrication

Driveline U-Joints and Profile Shields Lubrication

Lubrication instructions for driveline U-joints and shields.

CV Driveline U-Joints & Profile Shields Lubrication

Lubrication for Constant Velocity driveline U-joints and shields.

Telescoping Driveline Profiles With Zerks Lubrication

Lubrication for telescoping driveline profiles with grease fittings.

Further Driveline and Hitch Lubrication

Telescoping Driveline Profiles Without Zerks Lubrication

Lubrication for telescoping driveline profiles without grease fittings.

Pull-Type Hitch Lubrication

Lubrication requirements for the pull-type hitch.

Section 6: Specifications & Capacities

Model Numbers

Lists the model numbers covered in the manual.

Specifications and Capacities

Detailed technical specifications and capacities of the rotary cutters.

Section 7: Features & Benefits

Features of RCF(M)3696 & RCF(M)3610 Models

Lists the key features of the rotary cutter models.

Benefits of Rotary Cutter Features

Explains the advantages and benefits provided by the cutter's features.

Section 8: Troubleshooting

RCF(M)3696 & RCF(M)3610 Troubleshooting Chart

A chart detailing common problems, their causes, and solutions.

Section 9: Torque & Tire Inflation Charts

Torque Values Chart for Common Bolt Sizes

Provides torque specifications for various bolt sizes.

Additional Torque Values

Lists specific torque values for certain components.

Tire Inflation Chart

Specifies correct tire inflation pressures.

Section 10: Warranty

Land Pride Warranty Information

Details the warranty coverage, terms, and conditions for Land Pride products.

Land Pride RCF3696 User Manual

Table of Contents

Questions and Answers:

Land Pride RCF3696 Specifications

Summary

Rotary Cutters Overview

3-Point Rotary Cutter Setup

Semi-Mount Rotary Cutter Setup

Pull-Type Rotary Cutter Setup

Operator's Manual Information

Machine Identification and Dealer Information

Machine Identification Log

Dealer Contact Information

California Proposition 65 Warning

Important Safety Information

Safety at All Times

Look for the Safety Alert Symbol

Safety Precautions for Children

Safety Information Continued

Use A Safety Chain

Transport Safely

Tire Safety

Practice Safe Maintenance

Continued Safety Precautions

Prepare for Emergencies

Personal Protective Equipment and Fluid Hazards

Visibility and Operator Safety Features

Additional Safety Guidelines

Avoid Crystalline Silica Dust

Handle Chemicals Properly

Dig Safe - Avoid Underground Utilities

Safety Labels and Hazards

Rotating Driveline Contact Hazard

Thrown Object and Rotating Blade Hazard

Crushing, Run Over, and Rollover Hazards

Specific Safety Label Warnings

Guard Missing Hazard

Rotating Blades Hazard

Thrown Object Hazard

Introduction to Your Rotary Cutter

Application Overview

Using This Manual

Owner Assistance and Further Help

Section 1: Assembly & Set-Up

Tractor Requirements

Dealer Preparations

Pre-Assembly Checklist

Assembly Procedures

Gearbox Vent Plugs and Dipsticks

Tractor Shutdown Procedure

Getting Started with Cutter Types

3-Point Hitch Assembly

3-Point Assembly and Set-Up

Hitch Assembly (3-Point)

3-Point Driveline and Hose Hook-up

Spring Hose Loop Assembly (3-Point)

Driveline Installation (3-Point)

3-Point Tailwheel Assembly

RCF(M)3696 Tailwheels (3-Point)

RCF(M)3610 3-Point Tailwheel Assembly

RCF(M)3610 Tailwheels (3-Point)

RCF(M)3696 3-Point Hitch Hook-Up

RCF(M)3696 Hitch Hook-Up (3-Point)

RCF(M)3610 3-Point Hitch Hook-Up

RCF(M)3610 Hitch Hook-Up (3-Point)

3-Point Driveline Hook-up

Driveline Hook-up (3-Point)

3-Point Hydraulic and Hitch Pin

Hydraulic Hook-up Option (3-Point)

Hitch Pin Modification (3-Point & Semi)

Section 1: Assembly & Set-Up Continued

Semi-Mount Assembly and Set-Up

Spring Hose Loop Assembly (Semi-Mount)

Driveline Installation (Semi-Mount)

Semi-Mount Tailwheel Assembly

RCF(M)3696 Tailwheels (Semi-Mount)

RCF(M)3610 Semi-Mount Tailwheel Assembly

RCF(M)3610 Tailwheels (Semi-Mount)

Semi-Mount Hitch Hook-Up

Hitch Hook-Up (Semi-Mount)