Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 293
no secure credentials
Clears the RSA/DSA certificate selection for the HTTP server.
no secure port
Disables the HTTP Server SSL port.
port <number>
Sets the port number the HTTP server will use. <number> = port number.
secure credentials <text>
Selects the RSA/DSA certificates by name for the HTTP server.
secure port <number>
Sets the port number the HTTP server will use over SSL. <number> = port number.
secure protocols ssl3
disable
Disables the protocol.
secure protocols ssl3
enable
Enables the protocol.
secure protocols tls1.0
disable
Disables the protocol.
secure protocols tls1.0
enable
Enables the protocol.
secure protocols tls1.1
disable
Disables the protocol.
secure protocols tls1.1
enable
Enables the protocol.
secure protocols tls1.2
disable
Disables the protocol.
secure protocols tls1.2
enable
Enables the protocol.
show
Displays the current configuration.
show auth
Displays the HTTP server authentication settings.
show history
Displays the last 20 commands entered during the current CLI session.
show log
Displays the HTTP server log.
show statistics
Displays the HTTP statistics.
state disable
Disables the HTTP server.
state enable
Enables the HTTP server.
write
Stores the current configuration in permanent memory.
http post (config-action-http_post:wlan0 link state change) level commands
clrscrn
Clears the screen.
connection <instance>
Enters the next lower level. Specify the instance for the next lower level.
default mode
Sets default of simultaneous connection mode.
exit
Exits to the next higher level.
mode sequential
Sets sequential mode; will stop after first connection that goes through.
mode simultaneous
Sets simultaneous mode; will make all possible connections.
no reminder interval
Clears the HTTP Post reminder interval. HTTP Post is sent once only.
reminder interval
<minutes>
Sets the HTTP Post reminder interval.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
write
Stores the current configuration in permanent memory.
http post (config-action-http_post:usb0 link state change) level commands
clrscrn
Clears the screen.
connection <instance>
Enters the next lower level. Specify the instance for the next lower level.
default mode
Sets default of simultaneous connection mode.
exit
Exits to the next higher level.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm