Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 324
modem (tunnel-modem:1) level commands
clrscrn
Clears the screen.
connect string <text>
Sets the CONNECT string used in modem emulation. <string> = connect string.
default incoming connec-
tion
Default disables incoming network connections.
default response type
Default uses text type responses.
display remote ip disable
The incoming RING has nothing following it.
display remote ip enable
The incoming RING is followed by the IP address of the caller.
echo commands disable
Does not echo modem commands.
echo commands enable
Echoes modem commands.
echo pluses disable
Does not echo the +++ characters when entering modem command mode.
echo pluses enable
Echoes the +++ characters when entering modem command mode.
error unknown com-
mands disable
Returns OK on unknown AT commands.
error unknown com-
mands enable
Returns an error upon unknown AT commands.
exit
Returns to the tunnel level.
incoming connection
automatic
Automatically answer incoming network connections.
incoming connection
disabled
Disable incoming network connections.
incoming connection
manual
Wait for an ATA command before answering an incoming network connection.
no connect string
Removes optional CONNECT string information for modem emulation.
reassert
Asserts tunnel modem status with current configured values.
response type numeric
Uses numeric type responses.
response type text
Uses text type responses.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays tunnel modem status.
verbose response disa-
ble
Does not send Modem Response Codes.
verbose response enable
Sends Modem Response Codes out on the Serial Line.
write
Stores the current configuration in permanent memory.
ntp (config-clock-ntp) level commands
clrscrn
Clears the screen.
default server
Restores the default NTP server address.
exit
Exits to the next higher level.
server <text>
Sets the NTP server address.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
write
Stores the current configuration in permanent memory.
on scheduled reboot (config-action:on scheduled reboot) level commands
clrscrn
Clears the screen.
default delay
Resets alarm processing delay to its default value.
delay <seconds>
Sets the delay in processing the alarm. Alarm actions will not be executed if the cause is
corrected within this time.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm