Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 339
filter <instance>
Enters the next lower level. Specify the instance for the next lower level.
import filters disable
Do not import QoS filters from other interfaces.
import filters enable
Import QoS filters from other interfaces.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays the current status
state disable
Disables QoS.
state enable
Enables QoS.
uplink data speed <float-
ing point number>
Sets the maximum uplink speed in kbps.
write
Stores the current configuration in permanent memory.
qos (config-wlan-qos:wlan0) level commands
clrscrn
Clears the screen.
default uplink data speed
Restores the default uplink speed.
exit
Exit back to interface configuration level
filter <instance>
Enters the next lower level. Specify the instance for the next lower level.
import filters disable
Do not import QoS filters from other interfaces.
import filters enable
Import QoS filters from other interfaces.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays the current status
state disable
Disables QoS.
state enable
Enables QoS.
uplink data speed <float-
ing point number>
Sets the maximum uplink speed in kbps.
write
Stores the current configuration in permanent memory.
qos (config-ethernet-qos:eth0) level commands
clrscrn
Clears the screen.
default uplink data speed
Restores the default uplink speed.
exit
Exit back to interface configuration level
filter <instance>
Enters the next lower level. Specify the instance for the next lower level.
import filters disable
Do not import QoS filters from other interfaces.
import filters enable
Import QoS filters from other interfaces.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays the current status
state disable
Disables QoS.
state enable
Enables QoS.
uplink data speed <float-
ing point number>
Sets the maximum uplink speed in kbps.
write
Stores the current configuration in permanent memory.
reboot schedule (device-reboot-schedule) level commands
clrscrn
Clears the screen.
default hours
Restores the default hour of day for reboot schedule time.
default interval
Restores the default schedule interval.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm