Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 346
no normal message
Removes the normal message.
no reminder interval
Clears the SNMP Trap reminder interval. SNMP Trap is sent once only.
normal message <text>
Sets the message to be sent when the alarm turns off.
reminder interval
<minutes>
Sets the SNMP Trap reminder interval.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
state disable
Does not send SNMP Trap.
state enable
Sends SNMP Trap when alarm condition is met.
write
Stores the current configuration in permanent memory.
snmp trap (config-action-snmp_trap:eth0 link state change) level commands
alarm message <text>
Sets the message to be sent when the alarm turns on.
clrscrn
Clears the screen.
exit
Exits to the next higher level.
no alarm message
Removes the alarm message.
no normal message
Removes the normal message.
no reminder interval
Clears the SNMP Trap reminder interval. SNMP Trap is sent once only.
normal message <text>
Sets the message to be sent when the alarm turns off.
reminder interval
<minutes>
Sets the SNMP Trap reminder interval.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
state disable
Does not send SNMP Trap.
state enable
Sends SNMP Trap when alarm condition is met.
write
Stores the current configuration in permanent memory.
snmpd (config-snmp-snmpd) level commands
authentication password
<text>
Sets password used for authentication for agent.
authentication protocol
md5
Uses MD5 for authentication for agent.
authentication protocol
sha
Uses SHA for authentication for agent.
clrscrn
Clears the screen.
default authentication
protocol
Restores to default SNMPv3 authentication method: MD5 for agent.
default port
Restores the SNMP agent port to default: 161.
default privacy protocol
Restores to default SNMPv3 privacy encryption method: DES for agent.
default read community
Restores the SNMP read-only community to default: public
default read-only authen-
tication protocol
Restores to default SNMPv3 read-only authentication method: MD5 for agent.
default read-only privacy
protocol
Restores to default SNMPv3 read-only privacy encryption method: DES for agent.
default read-only security
Restores to default SNMPv3 read-only security method: Authentication, No Privacy for
agent.
default security
Restores to default SNMPv3 security method: Authentication, No Privacy for agent.
default system descrip-
tion
Restores the SNMP system description to its default.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm