Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 345
clrscrn
Clears the screen.
exit
Returns to the config level.
no system location
Clears the SNMP system location.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays the SNMP agent status.
snmpd
Enters the next lower level.
system location <text>
Sets the SNMP system location. <text> = location of device.
traps
Enters the next lower level.
write
Stores the current configuration in permanent memory.
snmp trap (config-action-snmp_trap:wlan0 link state change) level commands
alarm message <text>
Sets the message to be sent when the alarm turns on.
clrscrn
Clears the screen.
exit
Exits to the next higher level.
no alarm message
Removes the alarm message.
no normal message
Removes the normal message.
no reminder interval
Clears the SNMP Trap reminder interval. SNMP Trap is sent once only.
normal message <text>
Sets the message to be sent when the alarm turns off.
reminder interval
<minutes>
Sets the SNMP Trap reminder interval.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
state disable
Does not send SNMP Trap.
state enable
Sends SNMP Trap when alarm condition is met.
write
Stores the current configuration in permanent memory.
snmp trap (config-action-snmp_trap:usb0 link state change) level commands
alarm message <text>
Sets the message to be sent when the alarm turns on.
clrscrn
Clears the screen.
exit
Exits to the next higher level.
no alarm message
Removes the alarm message.
no normal message
Removes the normal message.
no reminder interval
Clears the SNMP Trap reminder interval. SNMP Trap is sent once only.
normal message <text>
Sets the message to be sent when the alarm turns off.
reminder interval
<minutes>
Sets the SNMP Trap reminder interval.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
state disable
Does not send SNMP Trap.
state enable
Sends SNMP Trap when alarm condition is met.
write
Stores the current configuration in permanent memory.
snmp trap (config-action-snmp_trap:on scheduled reboot) level commands
alarm message <text>
Sets the message to be sent when the alarm turns on.
clrscrn
Clears the screen.
exit
Exits to the next higher level.
no alarm message
Removes the alarm message.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm