Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 352
state enable
Enables the static route.
static route <number>
Change to config gateway static route level.
write
Stores the current configuration in permanent memory.
static route 2 (config-staticroute:2) level commands
clrscrn
Clears the screen.
default metric
Restores the metric to default value.
exit
Exits to the config-gateway level.
friendly name <text>
Set the friendly name for static route. <text> = friendly name
gateway <text>
Sets the gateway for static route network.
interface <text>
Sets the route interface <text> = interface name
metric <number>
Sets the metric for static route. <number> = metric
network <text>
Sets the IP address and network mask for static route network.
no friendly name
Remove the friendly name
no gateway
Clears the gateway for static route network.
no interface
Clears the route interface. The WAN interface is used if no interface is specified.
no network
Clears the IP address for static route network.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
state disable
Disables the static route.
state enable
Enables the static route.
static route <number>
Change to config gateway static route level.
write
Stores the current configuration in permanent memory.
static route 3 (config-staticroute:3) level commands
clrscrn
Clears the screen.
default metric
Restores the metric to default value.
exit
Exits to the config-gateway level.
friendly name <text>
Set the friendly name for static route. <text> = friendly name
gateway <text>
Sets the gateway for static route network.
interface <text>
Sets the route interface <text> = interface name
metric <number>
Sets the metric for static route. <number> = metric
network <text>
Sets the IP address and network mask for static route network.
no friendly name
Remove the friendly name
no gateway
Clears the gateway for static route network.
no interface
Clears the route interface. The WAN interface is used if no interface is specified.
no network
Clears the IP address for static route network.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
state disable
Disables the static route.
state enable
Enables the static route.
static route <number>
Change to config gateway static route level.
write
Stores the current configuration in permanent memory.
static route 4 (config-staticroute:4) level commands
clrscrn
Clears the screen.
default metric
Restores the metric to default value.
exit
Exits to the config-gateway level.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm