Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 73
protocol telnet
Uses Telnet protocol (with IAC) for accept mode tunneling.
secure protocols ssl3
disable
Disables the protocol.
secure protocols ssl3
enable
Enables the protocol.
secure protocols tls1.0
disable
Disables the protocol.
secure protocols tls1.0
enable
Enables the protocol.
secure protocols tls1.1
disable
Disables the protocol.
secure protocols tls1.1
enable
Enables the protocol.
secure protocols tls1.2
disable
Disables the protocol.
secure protocols tls1.2
enable
Enables the protocol.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays tunnel accept status.
start character <control>
Sets the accept mode start character. The character may be input as text, control, decimal,
or hex. A control character has the form <control>C. A decimal value character has the
form \99. A hex value character has the form 0xFF.
tcp keep alive <millisec-
onds>
Sets the TCP keep alive time. This is the initial keep alive timeout. <milliseconds> = timer
value, in milliseconds.
tcp keep alive interval
<milliseconds>
Enables TCP keep alive for accept mode tunneling and sets the timer. <milliseconds> =
TCP keep alive for accept mode in milliseconds.
tcp keep alive probes
<number>
Sets the number of TCP keep alive probes. <number> = number of TCP keep alive probes.
write
Stores the current configuration in permanent memory.
access point (config-access-point) level commands
channel <number>
Sets the channel on which the Access Point will operate.
channel selection auto-
matic
Sets channel selection to automatic.
channel selection config-
ured
Sets channel selection to configured.
clrscrn
Clears the screen.
default channel
Clears the Access Point channel setting.
default channel selection
Sets to default channel selection, which is 'Automatic'.
default first client connect
timeout
Sets default First Client Connect Timeout for SoftAP trigger mode.
default ip address
Restores IP address of Access Point to the default value.
default last client discon-
nect timeout
Sets default Last Client Disconnect Timeout for SoftAP trigger mode.
default mode
Restores the AP mode to the default value (Always Up).
default suite
Restores the security method (suite) to the default value (None).
dns redirect <text>
Set the DNS redirect. <text> = Hostname.
exit
Returns to the config level.
first client connect
timeout <seconds>
Sets the First Client Connect Timeout for SoftAP trigger mode in seconds.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm