Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 74
ip address <ip ad-
dress/cidr>
Sets the IP address of Access Point. Formats accepted: 192.168.1.1 (default mask)
192.168.1.1/24 (CIDR) "192.168.1.1 255.255.255.0" (explicit mask)
last client disconnect
timeout <seconds>
Sets the Last Client Disconnect Timeout for SoftAP trigger mode in seconds.
mode always up
Sets the AP mode to Always Up.
mode triggered
Sets the AP mode to Triggered.
multicast forwarding dis-
able
Disables Multicast Forwarding.
multicast forwarding en-
able
Enables Multicast Forwarding.
network name <text>
Set Network Name (SSID). <text> = Network Name(SSID).
no dns redirect
Clears the DNS redirect.
no network name
Clears Network Name (SSID).
no passphrase
Clears the password.
passphrase <text>
Sets the value for the password. <text> = put quotes around the characters (max 63).
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show status
Displays statistics.
ssid broadcast disable
Disables SSID Broacast.
ssid broadcast enable
Enables SSID Broadcast.
state disable
Disables Access Point.
state enable
Enables Access Point.
suite none
Sets the security suite to None.
suite wpa
Sets the security suite to WPA.
trigger ap
Triggers soft AP.
suite wpa2
Sets the security suite to WPA2.
write
Stores the current configuration in permanent memory.
action (config-action-select) level commands
clrscrn
Clears the screen.
eth0 link state change
Enters the eth0 link state change alarm level.
exit
Exits to the config level.
on scheduled reboot
Enters the on scheduled reboot alarm level.
show history
Displays the last 20 commands entered during the current CLI session.
usb0 link state change
Enters the usb0 link state change alarm level.
wlan0 link state change
Enters the wlan0 link state change alarm level.
write
Stores the current configuration in permanent memory.
advanced (config-profile-advanced:default_infrastructure_profile) level commands
apply wlan
Try out WLAN settings without saving them to Flash. If the settings do not work, when you
reboot the device, it will still have the original settings.
basic
Switch to basic level
clrscrn
Clears the screen.
default tx power maxi-
mum
Restores the maximum TX power to the default value (14 dBm).
exit
Exit to the profiles level
power management dis-
able
Disables power management.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm