EasyManuals Logo

Lantronix SGX 5150 Command Reference

Lantronix SGX 5150
372 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #77 background imageLoading...
Page #77 background image
5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 77
state disable
Disables the line so data cannot be sent/received.
state enable
Enables the line so data can be sent/received.
terminal <line>
Enters the configure-terminal level. <line> = number of the terminal line (serial port) to be
configured.
terminal network
Enters the configure-terminal level for the network.
threshold <bytes>
Sets the threshold in bytes. After this many bytes are received, they are forwarded without
delay.
tunnel <line>
Enters the tunnel level. <line> = number of the tunnel line (serial port) to be configured.
usb <line>
Enters the usb level. <line> = number of the line (usb port) to be configured.
write
Stores the current configuration in permanent memory.
bridge 1 (config-bridge:br0) level commands
auto detect ip address
disable
Disables learning the IPv4 address of the bridged client.
auto detect ip address
enable
Enables learning the IPv4 address of the bridged client.
bridging initial scan inter-
val <seconds>
Sets the scan interval before learning the IP address of the bridged client.
bridging ip address <IP
address>
Sets the Bridging IP Address.
bridging ipv6 address
<ipv6 address>
Sets the Bridging IPv6 Address. IPv6 addresses are written in eight groups of four hexa-
decimal digits separated by colons, such as 2001:0db8:85a3:0000:0000:8a2e:0370:7334
Network address ranges are written in CIDR notation. A network is denoted by the first
address in the block (ending in all zeroes), a slash (/), and a decimal value equal to the
size in bits of the prefix
bridging mode host
Sets the bridging mode to 'Host'.
bridging mode network
Sets the bridging mode to 'Network'.
bridging mode static net-
work
Sets the bridging mode to 'Static Network'.
bridging scan interval
<seconds>
Sets the scan interval after learning the IP address of the bridged client.
clrscrn
Clears the screen.
default bridging initial
scan interval
Restores the default initial scan interval.
default bridging mode
Restores the default bridging mode.
default bridging scan
interval
Restores the default scan interval.
default ethernet interface
Restores the default Bridging ethernet interface.
ethernet interface <text>
Sets the Bridging ethernet interface.
exit
Exits to the config level.
network access for gate-
way disable
Disables network access for gateway in transparent bridging mode.
network access for gate-
way enable
Enables network access for gateway in transparent bridging mode.
no bridging ip address
Removes the Bridging MAC Address.
no bridging ipv6 address
Removes the Bridging IPv6 Address.
no bridging mac address
Removes the Bridging MAC Address.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
show statistics
Show bridge statistics

Other manuals for Lantronix SGX 5150

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Lantronix SGX 5150 and is the answer not in the manual?

Lantronix SGX 5150 Specifications

General IconGeneral
CertificationFCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicatorsYes
Power requirements9 - 30 VDC
Power over Ethernet (PoE)No
Power consumption (typical)1.9 W
Storage temperature (T-T)-40 - 85 °C
Operating temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)5 - 95 %
Security algorithms802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication methodRADIUS
Ethernet LAN (RJ-45) ports1
Supported protocolsIPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band2.4 / 5 GHz
Cabling technology10/100BASE-T(X)
Networking standardsIEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates10, 100 Mbit/s
Weight and Dimensions IconWeight and Dimensions
Weight350 g
Dimensions (WxDxH)110 x 89 x 26 mm

Related product manuals