Lantronix SGX 5150 Command Reference

5: Commands and Levels
SGX™ 5150 IoT Device Gateway Command Reference 87
show history
Displays the last 20 commands entered during the current CLI session.
use proxy disable
Disables use of proxy server for this connection.
use proxy enable
Enables use of proxy server for this connection.
validate certificates disa-
ble
Disables certificate validation for Mach10 client.
validate certificates ena-
ble
Enables certificate validation for Mach10 client.
write
Stores the current configuration in permanent memory.
connection 1 (config-action-http_post-connection:wlan0 link state change:1) level commands
clrscrn
Clears the screen.
default local port
Uses a random port number as the local port.
default port
Sets default Port number.
default protocol
Sets default HTTP Protocol.
exit
Exits to the next higher level.
host <text>
Sets HTTP server IP address or hostname to be connected to.
local port <number>
Sets a specific port for use as the local port. <number> = the number of the port to use.
no host
Clears HTTP server IP address or hostname.
no password
Clears the Password.
no url
Clears HTTP request URL.
no username
Clears the Username.
password <text>
Sets the Password used to logon to HTTP server.
port <number>
Sets the Port number which HTTP server is listening to.
protocol http
Selects HTTP Protocol.
protocol https
Selects HTTPS Protocol.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
url <text>
Sets HTTP request URL following IP address or hostname.
username <text>
Sets the Username used to logon to HTTP server.
write
Stores the current configuration in permanent memory.
connection 1 (config-action-ftp_put-connection:wlan0 link state change:1) level commands
clrscrn
Clears the screen.
default filename
Sets default FTP remote Filename.
default local port
Uses a random port number as the local port.
default port
Sets default Port number.
default protocol
Sets default FTP Protocol.
default username
Sets default Username.
exit
Exits to the next higher level.
filename <text>
Sets FTP remote Filename.
host <text>
Sets FTP server IP address or hostname to be connected to.
local port <number>
Sets a specific port for use as the local port. <number> = the number of the port to use.
no host
Clears FTP server IP address or hostname.
no password
Sets default Password.
password <text>
Sets the Password used to logon to FTP server.
port <number>
Sets the Port number which FTP server is listening to.
protocol ftp
Selects FTP Protocol.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm