To Next PageTo Next Page
Need help?Do you have a question about the Laser Key Products 3D Pro Xtreme and is the answer not in the manual?
Specifications for the computer needed to operate the 3D Pro machine.
Explanation of the emergency stop button's function and operation for turning the machine on/off.
Step-by-step guide for downloading, installing, and activating the 3D Pro software.
Process for activating the 3D Pro software using site codes and license configuration.
Steps to install necessary drivers for the 3D Pro machine to communicate with the computer.
Steps to configure the COM port and driver settings for proper machine communication.
Troubleshooting steps for common "Communications Error" or "Board Not Found" issues.
Instructions on how to remove and replace the cutter or stylus in the spindle.
Guide on how to replace the tracer tip, including single-ended tracer installation.
Instructions on how to change jaws on the 3D Pro machine, focusing on Jaw 1 and Jaw 2.
Procedure for calibrating the cutter for Jaw 1 using the stylus.
Procedure for calibrating the tracer for Jaw 1.
Procedure for calibrating the cutter for Jaw 2.
Procedure for calibrating the cutter for Jaw 3 using the stylus.
Procedure for calibrating the tracer for Jaw 3.
Details on using Jaw 1 for high security keys and clamping with the tip stop.
Examples and instructions for clamping keys in Jaw 1 using tip and shoulder stops.
Instructions for using the 'B' side of Jaw 1 for specific key types.
Instructions for using Jaw 3, specifically for VAG (HU66) keys.
Notes on loosening Jaw 2 clamp and changing the jaw clamp.
How to clamp shoulder stop keys in Jaw 2 as per software instructions.
How to clamp tip stop keys in Jaw 2, ensuring correct placement.
Explanation of different cut types (Laser Cut, Plunge Cut) supported by the machine.
How to use the Standard Tracing Adapter for standard security keys in Jaw 1.
Instructions for clamping shoulder and tip stop keys correctly for tracing.
Steps to start the tracing process within the 3D Pro software.
Guidance on setting up software and matching Jaw 2 tracer settings to Jaw 1.
Information about the Tubular Jaw, including cutter and tracer setup.
Instructions for installing and using the Tubular Jaw for tracing and cutting keys.
How to find and select tubular key types within the 3D Pro software.
List of Tubular Key DSD numbers and instructions for searching by DSD.
Introduction to Tibbe keys and the Tibbe Adaptor, including how to insert the key.
Step-by-step guide for cutting a Ford Tibbe key using the Tibbe Adaptor and Jaw 1.
Step-by-step guide for cutting a Jaguar Tibbe key using the Tibbe Adaptor and Jaw 1.
Explanation of the three methods for selecting keys in the 3D Pro software.
How to back up, restore, and install the customer keys database.
Process for saving a key, including adding customer information.
Steps to load previously saved keys for a selected customer.
How to search for existing customers or add new ones to the database.
Explanation of the X, Y, Z axes for Jaws 1, 3 and X, Y axes for Jaw 2.
Using a Honda key example to adjust space and depth settings in the software.
Example of trace readings and how they relate to key measurements.
Detailed steps for making space and depth adjustments in Jaw 1 using the software.
Detailed steps for adjusting space and depth for Jaw 2, using a Schlage key example.
Instructions on using calipers to measure key depths and spacing for adjustments.
Specific instructions for adjusting depth offset for Jaw 2 based on measurements.
How to access and use the "Show Key Information" feature in the software.
Explanation of the "Half Cut" button and its use with Determinators.
Functionality of Reset, Trace, Enter, and Start buttons in the software.
Understanding DSD numbers and how to use the "Search" tab.
Information on identifying the correct key blank and manufacturer.
Understanding values for spaces, depths, and track types.
Explanations of cut type, jaw type, and jaw clamp usage.
Describes stop types and explains comment boxes for notes.
Explains side spaces and the machine's operational status.
Instructions for using the re-connect button when the board cannot be found.
Overview of the Key Editor for editing key cutting and tracing parameters.
Controls for key center location and flat width dimensions.
Controls for cutter/tracer height and plunge cut angles.
Controls for spaces/depths and option for user notes.
Using Half Cut Depth and understanding Tracing Data.
Pre-defined parameters for key tip cutting, not user-adjustable.
Steps to resolve "Communications Error" or "Board Not Found" issues.
Troubleshooting for machine humming and software load bar freezing.
Flowchart for diagnosing and resolving connection errors.
Recommendations and safety guidelines for using an inverter with the 3D Pro.
Visual example of properly grounding an inverter to the vehicle chassis.
Step-by-step instructions for safely changing the fuses in the machine.
List of optional accessories available for the 3D Pro key machine.
General| Brand | Laser Key Products |
|---|---|
| Model | 3D Pro Xtreme |
| Category | Industrial Equipment |
| Language | English |
