latch Hub User Manual

Hub Installation Guide Ve rsion 1.032 33
If the hub does not operate:
•
•
•
•
Safety Instructions
•
•
•
•
•
•
Safety Instructions
Conguration & Commissioning instructions can be found in more detail in the Technical
Certication Training as well as on the support website at support.latch.com
Troubleshooting
Ensure the hub is powered with DC power. Do not use AC power.
Ensure the input voltage if using 2 wire is 12 volts DC
Ensure the input PoE Type if using PoE is 802.3bt 30W+
Further troubleshooting information is available on the support website at support.latch.com
This product shall be installed and serviced by certied professionals only
Locations and wiring methods shall be in accordance with the National Electrical Code,
ANSI/NFPA 70
For PoE connections, installation must be done in accordance with NFPA 70: Article 725.121,
Power Sources for Class 2 and Class 3 Circuits
There are no replacement parts available for this product
Correct wiring insulation should be used during installation to prevent the risk of electrical
shock
Model: Hub
Warning
Service Information
Conguration & Commissioning instructions can be found in more detail in the Technical
Certication Training as well as on the support website at support.latch.com
Applicable Products
This installation guide applies to products with the following designators on the label:
•
Exposure to Radio Frequency (RF) Energy
This device meets the government’s requirements for exposure to radio waves. This device is
designed and manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission (FCC) and the Innovation, Science,
and Economic Development (ISED) Canada.
The product may contain an internal lithium manganese dioxide, vanadium pentoxide, or
alkaline battery or battery pack. There is risk of re and burns if the battery pack is not
handled properly.
Do not expose to temperatures higher than 50° C (122° F).
To reduce potential safety issues, only the battery provided with the product, a replacement
battery provided by Latch, or a compatible battery purchased as an accessory from Latch
should be used with the product.
To reduce the risk of re or burns, do not disassemble, crush, puncture, short external
contacts, or dispose of in re or water.
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
Do not ingest battery, a Chemical Burn Hazard.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away
from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
Leaving a battery in an extremely high temperature surrounding environment can result in an
explosion or the leakage of ammable liquid or gas.
A battery subjected to extremely low air pressure may result in an explosion or the leakage of
ammable liquid or gas.
•
•
•
•
•
•
•
•
•
•
•
L’appareil ne doit pas produire de brouillage, et
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Industry Canada (IC) Compliance Statement
This device complies with applicable Industry Canada RSSs. Operation is subject to the
following two conditions: (1) This device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the
device.
To satisfy RF exposure requirements, this device and its antenna must operate with a separation
distance of at least 20 centimeters from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1.
2.
Pour remplir les conditions requise sur l’exposition des fréquences radios, cet appareil et les
antennes doivent fonctionner avec une distance minimum de 20 centimètres avec toutes les
personnes et ne doivent pas être placés ou fonctionner en conjonction avec tout autre antenne
ou émetteur.

latch Hub Specifications

General

Brand	latch
Model	Hub
Category	Switch
Language	English