Launch CNC-603A User Manual

LAUNCH CNC-603A Injector Cleaner & Tester User Manual
i
All rights reserved! Any company or individual person shall not copy or backup this user manual in any format
(electronic, mechanical, photocopying, recording or other formats) without written permission from Launch Tech
Co., Ltd (hereinafter referred to as "Launch"). The manual is for the use of the products manufactured by Launch,
which shall not assume any responsibility for the consequences arising from the use of it to guide the operations
of other equipment.
Launch and its branches will not bear any liability for the fees and expenses incurred by equipment damage or
loss due to accidents caused by users or third parties, misuses and abuses, unauthorized modifications and repairs,
or operations and services not following launch’s instructions.
Launch assumes no responsibility for device damages or problems resulted from the usage of other parts or
consumables, rather than original products of launch or products approved by the company.
Official statement: the mentioning of the names of other products in this manual is to illustrate how to use the
device, with the ownership of the registered trademarks belonging to the owners.
The device is intended for the use of professional technicians or maintenance and repair personnel.
Registered Trademark
Launch has registered its trademark in china and several other countries, and the logo is . Other
trademarks, service marks, dot names, icons, company names of launch mentioned in the user manual all belong
to launch and its subsidiaries. In those countries where trademarks, service marks, dot names, icons, company
names of launch have not been registered yet, launch declaims the right for its unregistered trademarks, service
marks, dot names, icons, and company names. Trademarks of other products and company names mentioned in
this manual are still owned by the original registered companies. Without written agreement from the owner, no
person is allowed to use the trademarks, service marks, domain names, icons and company names of Launch or of
other mentioned companies. You can visit http://www.cnlaunch.com, or write to Customer Service Center of
Launch Tech Co., Ltd at Launch Industrial Park, North of Wuhe Avenue, Banxuegang, Longgang District,
Shenzhen, P.R. China, to get contact with Launch for the written agreement on the usage of the user manual.

Launch CNC-603A Specifications

General

Model	CNC-603A
Ultrasonic Cleaning Power	100W
Power Supply	220V, 50Hz
Rotating Speed Range	0-3000rpm
PWM Pulse Width	0-100%
Control System	Microcomputer Control
Spindle Speed	0-3000rpm
Spindle Power	1.5kW
Power	1.5kW

Summary

Registered Trademark Information

Important Safety Instructions

Key Safety Guidelines

Essential precautions for safe operation, handling, and maintenance of the injector cleaner and tester.

Introduction to CNC-603A Injector Cleaner & Tester

Brief Product Overview

Overview of the CNC-603A Injector Cleaner & Tester and its primary purpose.

Core Functions and Features

Details on the core functionalities and distinctive features of the CNC-603A injector cleaner.

Working Environment and Specifications

Technical specifications and environmental requirements for operating the CNC-603A injector cleaner.

Structure of CNC-603A Injector Cleaner & Tester

System Component Diagram

Visual representation and labeling of the main components of the CNC-603A injector cleaner.

Control Panel Interface

Description and illustration of the control panel interface and its buttons.

Installation and Connection Guide

Initial Unit Installation

Guidance on physically setting up the CNC-603A injector cleaner on a flat surface.

Power Connection Procedure

Instructions for connecting the power line to the main unit of the CNC-603A injector cleaner.

Injector Cleaning and Testing Procedures

Pre-Operation Preparations

Essential preparation steps before performing injector cleaning and testing procedures.

Cleaning and Testing Sequence

Recommended order for performing various cleaning and testing operations on injectors.

Post-Operation Cleanup Procedures

Procedures for cleaning the equipment after completing injector cleaning and testing.

Operation Processes

Uniformity and Sprayability Test

How to perform uniformity and sprayability tests on fuel injectors.

Leakage Test Procedure

Steps for conducting a leakage test on fuel injectors to detect leaks.

Injecting Flow Test Guide

Procedure for measuring the fuel injection quantity over a specific time.

Automatic Test (Auto. Test) Guide

Detailed guide for performing comprehensive automated injector tests under various conditions.

Ultrasonic Cleaning Method

Method for cleaning injectors using ultrasonic waves and cavitation.

On-Vehicle Cleaning Process

Procedure for cleaning injectors while they are installed on the vehicle.

Line Connection for On-Vehicle Cleaning

Instructions for connecting hoses for on-vehicle injector cleaning procedures.

Post On-Vehicle Cleaning Procedures

Steps to clean up the workspace and equipment after on-vehicle cleaning.

Selecting Operating Language

How to change the operating language of the CNC-603A Injector Cleaner & Tester.

Checking Software Version Information

How to check the current software version of the device.

Service and Maintenance

Handling, Storage, and Installation Environment

Guidelines for safely handling, storing, and installing the injector cleaner.

Common Replacement Parts & Consumables

Information on common replacement parts and consumables for the injector cleaner.

Troubleshooting Common Problems

Common issues, their causes, and solutions for the injector cleaner.

Commissioning and Main Parts Identification

Schematic Diagram and Parts List

Detailed schematic and list of all parts for the CNC-603A Injector Cleaner & Tester.

Appendix I: Fuel System Pressure Guide

Warranty and Support Information

Warranty Disclaimer

Legal statement regarding warranty coverage and limitations for Launch products.

Parts Ordering & Customer Service

How to order parts and contact customer service for support and repairs.

Product Statement and Contact