Launch LTR-03 - User Manual

Safety Instructions
Any maintenance and repair work must be carried out
by trained experts. Failure to do so may result in the
failure of the TPMS sensor. LAUNCH does not
assume any liability in case of faulty or incorrect
installation of the unit.
CAUTION
Do not race with the vehicle on which the LTR-01
RF sensor is mounted, and always keep the
drive speed under 240km/h.
To guarantee optimal performance, the sensors
may only be installed with original valves and
accessories provided by LAUNCH.
Make sure to program the sensors using
LAUNCH-specific TPMS tool prior to
installation.
Do not install programmed TPMS sensors in
damaged wheels.
After installing the TPMS sensor, test the
vehicle’s TPMS following the steps described in
the original manufacturer’s user manual to
confirm proper installation.
When mounting/dismounting the wheel, follow
the operation guideline of wheel changer
manufacturer strictly.
RF-Sensor
QuickStartGuide
LTR-03
IMPORTANT: Read these instructions
carefully and use this unit properly before
operating. Failure to do so may cause damage
and/or personal injury and will void the product
warranty.
www.x431.com
LAUNCH
+86-755-84557891
overseas.service@cnlaunch.com
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
FCC Warning
- Reorient or relocate the receiving antenna.
Note: Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment. This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.This
equipment should be installed and operated with
minimum distance 20cm between the radiator &your
body.
Disclaimer of Warranties and
Limitation of Liabilities
All information, illustrations, and specifications in this
manual are based on the latest information available at
the time of publication. The right is reserved to make
changes at any time without notice. We shall not be
liable for any direct, special, incidental, indirect
damages or any economic consequential damages
(including the loss of profits) due to the use of the
document.

Summary

Safety Instructions

Maintenance and Repair Expertise

All maintenance and repair work must be performed by trained experts to prevent sensor failure.

Wheel Changer Guidelines

Follow the wheel changer manufacturer's operational guidelines strictly when mounting or dismounting the wheel.

Vehicle Speed and Racing

Do not race the vehicle and always keep the drive speed under 240km/h when the RF sensor is mounted.

Component Compatibility

For optimal performance, sensors must be installed with original LAUNCH valves and accessories.

FCC Warning and Compliance

Modification Restrictions

Unauthorized modifications may void user's authority to operate the equipment.

Interference Handling

Describes measures to correct radio interference if equipment causes it.

Radiation Exposure Limits

Equipment complies with FCC radiation exposure limits; maintain 20cm distance from radiator.

Components & Controls

Installation Steps

Loosening the Tire

Remove valve cap and nut, then use tire bead loosener to break the tire bead.

Dismounting the Tire

Clamp tire, adjust valve, and use tire tool to dismount the tire bead.

Mounting the Sensor and Valve

Place sensor through valve hole, then tighten nut to the correct torque.

Remounting the Tire

Place tire on rim, ensuring valve is opposite to fitting mount, then mount tire over rim.

Warranty Information

Launch LTR-03 Specifications

General

Brand	Launch
Model	LTR-03
Category	Accessories
Language	English