EasyManuals Logo

LC-POWER LC-DOCK-U3-III User Manual

LC-POWER LC-DOCK-U3-III
3 pages
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
Installation guide
LC-DOCK-U3-III - USB 3.0 Dual Bay Docking Station for 2x 2,5”/3,5” SATA HDDs/SSDs
-----------------------------------------------------------------------------------------------------------------------------------------------------------------
Important note :
1.
Before cloning a hard disk drive, please disconnect the USB 3.0 cable from the docking station.
If the mentioned cable is connected during the cloning process, it may cause data corruption on
the hard disk drives.
2.
Please make sure you put the correct hard disk drive into the correct HDD bay before cloning.
Otherwise this may cause a data loss.
3.
The capacity of the target hard disk drive (must be put in the target HDD bay) must be equal or
larger than the capacity of the source hard disk drive.
Please follow the steps below to enable the hardware clone process:
1.
Install two hard disk drives into the dock. Make sure the correct drives are properly installed to source
bay (HDD A) and target bay (HDD B).
2.
Remove the USB cable from the docking station, connect the power adapter and press the power
button to power on the docking station.
3.
Press and hold the CLONE button for 3 seconds to start the duplication. The percentage LED
indicators located next to the “Clone” button will begin to blink. If you do not hold the clone button for
3 seconds, you need to start the process again.
4.
As the duplication process progresses, the LED indicator will blink regarding the cloning status
(25%, 50%, 75%, 100%).
5.
When the duplication process has completed, the percentage LED indicator will lighted continuously.
Press the power button on the rear side of the docking station to turn off the docking station.
6.
You can now safely remove the hard disk drives from the docking station.
Silent Power Electronics GmbH, Formerweg 8, 47877 Willich, Germany, www.lc-power.com
Page 3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the LC-POWER LC-DOCK-U3-III and is the answer not in the manual?

LC-POWER LC-DOCK-U3-III Specifications

General IconGeneral
Storage media typeHDD, SSD
Storage drive interfaceSerial ATA
Maximum storage capacity4000 TB
Storage drive sizes supported2.5, 3.5 \
Number of storage drives supported2
USB 3.2 Gen 1 (3.1 Gen 1) ports quantity1
Standard interfacesUSB 3.2 Gen 1 (3.1 Gen 1)
Hot-swapYes
MaterialAluminium, Metal, Plastic
Product colorBlack
Maximum data transfer rate5 Gbit/s
Mac operating systems supportedMac OS 9.1
Windows operating systems supportedWindows 10 Education, Windows 10 Education x64, Windows 10 Enterprise, Windows 10 Enterprise x64, Windows 10 Home, Windows 10 Home x64, Windows 10 Pro, Windows 10 Pro x64, Windows 7 Enterprise, Windows 7 Enterprise x64, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 8, Windows 8 Enterprise, Windows 8 Enterprise x64, Windows 8 Pro, Windows 8 Pro x64, Windows 8 x64, Windows 8.1, Windows 8.1 Enterprise, Windows 8.1 Enterprise x64, Windows 8.1 Pro, Windows 8.1 Pro x64, Windows 8.1 x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Enterprise, Windows Vista Enterprise x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64
Harmonized System (HS) code84733080
Weight and Dimensions IconWeight and Dimensions
Depth79 mm
Width138 mm
Height94 mm
Weight291 g

Related product manuals