LEGA
LEGA LEGA
LEGA
srl
srlsrl
srl
C
CC
Costruzioni
ostruzioni ostruzioni
ostruzioni A
AA
Apistich
pistichpistich
pistiche
ee
e
–
––
–
via Maestri del Lavoro 23
via Maestri del Lavoro 23 via Maestri del Lavoro 23
via Maestri del Lavoro 23 –
––
–
48018 Faenza
48018 Faenza48018 Faenza
48018 Faenza
www.legaitaly.com
www.legaitaly.com www.legaitaly.com
www.legaitaly.com -
--
-
Tel 054626834
Tel 054626834 Tel 054626834
Tel 054626834 –
––
–
Fax 054628279
Fax 054628279 Fax 054628279
Fax 054628279 –
––
–
P.iva 00043230390
P.iva 00043230390P.iva 00043230390
P.iva 00043230390
5 / 16
1.0
1.01.0
1.0
GENERAL SAFETY DIRECTIONS
GENERAL SAFETY DIRECTIONSGENERAL SAFETY DIRECTIONS
GENERAL SAFETY DIRECTIONS
READ THIS MANUAL THROUGHOUT BEFORE USING THE MACHINE
This handbook forms an integral part of the machine and should be kept with it throughout its working life.
This handbook forms an integral part of the machine and should be kept with it throughout its working life.This handbook forms an integral part of the machine and should be kept with it throughout its working life.
This handbook forms an integral part of the machine and should be kept with it throughout its working life.
The machine includes dangerous electrically live and moving parts, which can cause serious damages to
cause serious damages to cause serious damages to
cause serious damages to
persons or property in case of:
persons or property in case of:persons or property in case of:
persons or property in case of:
- incorrect use
- removal of guards or disconnection of safety devices
- poor inspection and servicing
- tampering with the electric system
These directions must be completed and updated according to applicable legal provisions and technical safety
standards.
The manufacturer may not be held responsible for failures, breaks or accidents resulting from incorrect use of the
The manufacturer may not be held responsible for failures, breaks or accidents resulting from incorrect use of the The manufacturer may not be held responsible for failures, breaks or accidents resulting from incorrect use of the
The manufacturer may not be held responsible for failures, breaks or accidents resulting from incorrect use of the
machine or failure to follow the directions
machine or failure to follow the directions machine or failure to follow the directions
machine or failure to follow the directions contained in this manual.
contained in this manual.contained in this manual.
contained in this manual.
1.1
1.11.1
1.1
IDENTIFICATION OF THE MACHINE
IDENTIFICATION OF THE MACHINEIDENTIFICATION OF THE MACHINE
IDENTIFICATION OF THE MACHINE
Uncapping machine suitable for bench mounting with vibrating blade. Compact machine with an electrically heated knife
blade with thermostat-controlled resistor.
Blade vibration is powered by an electric gearmotor. This movement, combined with blade heating, ensures accurate,
fast cutting.
1.2
1.21.2
1.2
TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONSTECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
Total absorption w 880
Motor power w 250
Input voltage V 220
Frequency Hz 50
Weight Kg 15
Overall dimensions mm 520x420x250
1.3
1.31.3
1.3
MACHINE OPERATORS
MACHINE OPERATORSMACHINE OPERATORS
MACHINE OPERATORS
CAUTION!
CAUTION!CAUTION!
CAUTION! FOR SAFETY PURPOSES, THIS MACHINE SHOULD BE USED BY SKILLED STAFF ONLY, AWARE
OF THE INSTRUCTIONS CONTAINED IN THIS MANUAL WHICH FORMS AN INTEGRAL PART OF THE
MACHINE.
The uncapping machine has been designed for operation by a single worker.
Basic technical and mechanical skills are required to correctly operate the machine and carry out maintenance
and basic servicing.
2.0
2.02.0
2.0
MACHINE ADJUSTMENT BEFORE START
MACHINE ADJUSTMENT BEFORE STARTMACHINE ADJUSTMENT BEFORE START
MACHINE ADJUSTMENT BEFORE START-
--
-UP
UP UP
UP
Place the machine on an uncapping bench then connect it to the power line.
Adjust the distance between frame holder guides according to the width of the frames to uncap, then tighten
the guide screws.
Adjust the angle of the guide-supporting frame by turning the knobs (1). Different frame angles mean different
levels of blade action and hence, difference cutting depths. When the frame has reached full inclination, the
blade will cut flush with the wooden frame.
To Next Page
Loading...