Need help?Do you have a question about the Legacy LA690 and is the answer not in the manual?
Gold-plated terminals for high conductivity and minimum impedance loss.
Protects amplifier and automobile electrical system from short circuits.
Terminals for connecting the power supply to the amplifier.
Connects speaker outputs from head unit when no RCA outputs are available.
Gold-plated RCA jacks for connecting head unit RCA outputs.
Matches head unit output to amplifier; reduce if distortion occurs.
Illuminates when the REMOTE ON system is turned on.
Gold-plated terminals for high conductivity and minimum impedance loss.
Protects amplifier and automobile electrical system from short circuits.
Terminals for connecting the power supply to the amplifier.
Connects speaker outputs from head unit when no RCA outputs are available.
Gold-plated RCA jacks for connecting head unit RCA outputs.
Matches head unit output to amplifier; reduce if distortion occurs.
Illuminates when the REMOTE ON system is turned on.
Gold-plated terminals for high conductivity and minimum impedance loss.
Protects amplifier and automobile electrical system from short circuits.
Terminals for connecting the power supply to the amplifier.
Matches head unit output to amplifier; reduce if distortion occurs.
Selects FULL, HPF, or LPF mode for crossover system.
Adjusts bass signal level sent to speakers.
Adjusts crossover frequency (35 Hz to 350 Hz) for subwoofers.
Adjusts crossover frequency (80 Hz to 2.5 kHz) for tweeters.
Connects speaker outputs from head unit when no RCA outputs are available.
Gold-plated RCA jacks for connecting head unit RCA outputs.
Illuminates when the REMOTE ON system is turned on.
Illuminates when overload, short circuit, or thermal conditions occur.
Port for connecting the remote bass boost control wire.
Gold-plated terminals for high conductivity and minimum impedance loss.
Protects amplifier and automobile electrical system from short circuits.
Terminals for connecting the power supply to the amplifier.
Matches head unit output to amplifier; reduce if distortion occurs.
Selects FULL, HPF, or LPF mode for crossover system.
Adjusts bass signal level sent to speakers.
Adjusts crossover frequency (35 Hz to 350 Hz) for subwoofers.
Adjusts crossover frequency (80 Hz to 2.5 kHz) for tweeters.
Connects speaker outputs from head unit when no RCA outputs are available.
Gold-plated RCA jacks for connecting head unit RCA outputs.
Illuminates when the REMOTE ON system is turned on.
Illuminates when overload, short circuit, or thermal conditions occur.
Port for connecting the remote bass boost control wire.
Guide for connecting +12V, Ground, and REMOTE terminals for amplifier power.
Safety and installation advice to prevent damage and ensure proper function.
Steps for initial setup and adjusting level controls for optimal performance.
Diagram showing RCA cable connections for low-level stereo inputs.
Diagram showing speaker wire connections for high-level stereo inputs.
Shows Y-adapter usage for 4CH amps from a 2CH source.
Shows direct connection for 4CH amps from a 4CH source.
Connects front speaker outputs from head unit to 4CH amp high-level inputs.
Connects rear speaker outputs from head unit to 4CH amp high-level inputs.
Shows how to connect for bridged mono operation on 2CH amps.
Shows how to achieve 4CH bridged input from a 2CH source.
Illustrates connecting speakers for basic stereo operation on 2CH amps.
Illustrates connecting speakers for basic 4CH operation.
Connects a single speaker for bridged mono output, minimum 4 Ohms.
Connects speakers for 2CH mono-bridged output, minimum 4 Ohms.
Checks for power, ground, fuses, and protection LED status.
Guides on isolating noise sources and setting input levels.
Troubleshoots speaker shorts, volume settings, and faulty amplifiers.
Checks impedance, shorts, and airflow for overheating issues.
Checks level controls, crossover frequencies, and speaker shorts.
Identifies poorly-grounded RCA patch cords as the common cause.
Details the two-year limited warranty for material and workmanship defects.
Instructions for packing, including required documentation and fees.
Provides contact information for technical assistance and operating hours.
General| Channels | 6 |
|---|---|
| THD | <0.05% |
| Frequency Response | 20Hz - 20KHz |
| RMS Power at 4 Ohms | 60W x 6 |
| Input Impedance | 10k Ohms |
| Fuse Rating | 25A |
To Next Page
