Need help?Do you have a question about the Legacy LA790 and is the answer not in the manual?
Lists RMS and maximum output power for various models and impedance loads.
Specifies the range of audio frequencies the amplifier can accurately reproduce.
Details the impedance requirements for both low-level and high-level audio inputs.
Indicates the voltage levels required from the head unit for proper operation.
Specifies the operational voltage range and ground requirements for the amplifier.
Lists acceptable speaker impedance for stereo and bridged mono configurations.
Shows the maximum electrical current the amplifier can consume under load.
Provides the physical dimensions (Width x Height x Length) of the amplifiers.
Indicates the weight of the amplifiers in pounds and kilograms.
Gold-plated terminals for high conductivity and easy wiring in tight situations.
Protects the amplifier and vehicle electrical system from short circuit conditions.
Terminals for connecting the amplifier to the vehicle's power source.
Connects to car stereo speaker outputs if RCA jacks are unavailable.
Connects to RCA outputs from the head unit using patch cords.
Matches head unit output to amplifier; reduce if distortion occurs.
Illuminates when the REMOTE ON system is activated.
Gold-plated terminals for high conductivity and easy wiring in tight situations.
Protects the amplifier and vehicle electrical system from short circuit conditions.
Terminals for connecting the amplifier to the vehicle's power source.
Connects to car stereo speaker outputs if RCA jacks are unavailable.
Connects to RCA outputs from the head unit using patch cords.
Matches head unit output to amplifier; reduce if distortion occurs.
Illuminates when the REMOTE ON system is activated.
Gold-plated terminals for high conductivity and easy wiring in tight situations.
Protects the amplifier and vehicle electrical system from short circuit conditions.
Terminals for connecting the amplifier to the vehicle's power source.
Matches head unit output to amplifier; reduce if distortion occurs.
Selects full range, high-pass filter (HPF), or low-pass filter (LPF).
Increases the bass signal level sent to the speakers.
Adjusts crossover frequency (35 Hz to 350 Hz) for subwoofers.
Adjusts crossover frequency (80 Hz to 2.5 kHz) for tweeters.
Connects to car stereo speaker outputs if RCA jacks are unavailable.
Connects to RCA outputs from the head unit using patch cords.
Illuminates when the REMOTE ON system is activated.
Illuminates when amplifier is disabled due to overload or thermal issues.
Connection point for the optional remote bass boost control.
Gold-plated terminals for high conductivity and easy wiring in tight situations.
Protects the amplifier and vehicle electrical system from short circuit conditions.
Terminals for connecting the amplifier to the vehicle's power source.
Matches head unit output to amplifier; reduce if distortion occurs.
Selects full range, high-pass filter (HPF), or low-pass filter (LPF).
Increases the bass signal level sent to the speakers.
Adjusts crossover frequency (35 Hz to 350 Hz) for subwoofers.
Adjusts crossover frequency (80 Hz to 2.5 kHz) for tweeters.
Connects to car stereo speaker outputs if RCA jacks are unavailable.
Connects to RCA outputs from the head unit using patch cords.
Illuminates when the REMOTE ON system is activated.
Illuminates when amplifier is disabled due to overload or thermal issues.
Connection point for the optional remote bass boost control.
Instructions for connecting the amplifier's power, ground, and remote terminals.
Important safety and installation guidelines for mounting the amplifier.
Steps for initial setup, including adjusting level controls and checking for noise.
Diagram showing how to connect a stereo head unit using RCA cables.
Diagram showing how to connect using speaker wires from the head unit.
Connecting a 2-channel head unit to a 4-channel amplifier using Y adapters.
Connecting a 4-channel head unit to a 4-channel amplifier.
Diagram showing high-level connection for 4-channel amps using speaker wires.
Diagram for connecting a 2-channel head unit in bridged mode for 2CH amplifiers.
Connecting a 2-channel head unit for bridged 4-channel operation.
Diagram showing how to connect left and right speakers for stereo output.
Diagram showing how to connect front and rear speakers for 4-channel output.
Diagram for connecting a single speaker in bridged mono mode (min 4 Ohms).
Diagram for connecting speakers in bridged mono mode (min 4 Ohms) for 4CH amps.
Checks for power, ground, fuse, and protection LED issues when amplifier is dead.
Diagnosing and resolving noise issues like alternator whine or ground loops.
Troubleshooting steps when the protection indicator is illuminated.
Identifying causes for overheating, such as impedance or airflow issues.
Troubleshooting distorted audio output from the amplifier.
Resolving high-frequency squeal, often caused by RCA cable grounding.
Details the two-year warranty terms, exclusions, and return procedures.
Contact information and operating hours for technical assistance.
General| Channels | 4 |
|---|---|
| Signal to Noise Ratio | >90dB |
| THD at RMS Output | <0.05% |
| Fuse Rating | 25A |
| Frequency Response | 20Hz-20kHz |
| Input Sensitivity | 200mV-6V |
To Next Page
