Leigh Country CHAR-LOG Series User Manual

PARTS AND HARDWARE LIST
1 2
65
A B
C
D E F
3
4
X 1pc
7
X 1pc X 8pcs X 1pc
8
Mallet
13mm Socket
& Wrench
Phillips
Screwdriver
Tools Required For Assembly
LEG-UPPER
CHAR-LOG WINDMILL SERIES
Recessed Hole
ITEM # TX 20010, TX 20011, TX 22002, TX 26501 & TX 93485
Pre-Checked
Assembly video available at:
www.Youtube.com/LeighCountry.com
Tools Included
LEG-LOWER
UPPER SUPPORT
X 4pcs
LOWER SUPPORT
X 4pcs
X 25pcs
Power tools are not recommended while assembling this product.
SCREW
S04-3
X 16pcs
SCREW
S04-7
WINDMILL HEAD
X 8pcs
N08-8
NUT & BOLT NUT & BOLT
X 16pcs
N08-12
X 4pcs
STAKE
X 4pcs
CLAMP
SHAFT CROSS BRACE PLATFORM
ΦΦ 0.3”x4.7”0.1”x3”
Φ
0.165”x1.4”
Φ 0.17”x2.8”
1P & 1S x4 2P & 2S x4
IMPORTANT: READ CAREFULLY BEFORE BEGINNING
1. Do not tighten bolts until fully assembled.
2. Recessed holes to face outward.
3. Insert bolts with washer and secure with washer and nut.
4. Pre-checked side must always face downward or inward.

Leigh Country CHAR-LOG Series Specifications

General

Brand	Leigh Country
Model	CHAR-LOG Series
Category	Farm Equipment
Language	English

Summary

Important Pre-Assembly Instructions

Assembly Guidance & Bolt Tightening

Follow pre-assembly steps, ensure correct bolt/hole orientation and tighten last.

Parts and Hardware List

Major Components

Lists main parts of the windmill: legs, supports, shaft, platform, and head.

Hardware and Fasteners

Details nuts, bolts, screws, clamps, and stakes required for assembly.

Assembly Instructions

Step 1: Connect Legs

Connect upper and lower leg parts using specified bolts.

Step 2: Attach Supports

Connect Upper Support and Lower Support between legs using bolts.

Step 3: Fit Shaft

Install the shaft at the top of the legs and secure with screws.

Step 4: Attach Platform and Braces

Slide platform through shaft, affix cross braces with screws.

Step 5: Assemble Windmill Head

Instructions for assembling the windmill head unit.

Step 6: Mount Head and Optional Anchoring

Place head on shaft, secure it, and optional steps for clamps and stakes.

Windmill Head Assembly Details

Windmill Head Parts and Hardware

Lists components for the windmill head: main shaft, tail, fan blades, hob, ring, and fasteners.

Tail Assembly Procedure

Instructions for assembling the tail section of the windmill head.

Fan Head Assembly Procedure

Instructions for assembling the fan blades and hub.

Ring Insertion

Procedure for inserting the ring through fan blade holes.

Attaching Fan Head to Shaft

Attaching the assembled fan head to the main shaft.

Windmill Anchoring Instructions

Anchoring Responsibility and Method

User's responsibility for location and anchoring; outlines a recommended method.

Tools and Materials for Anchoring

Lists necessary tools like a post hole digger and concrete mix for footings.

Concrete Footing Specifications

Recommends 4"-6" diameter x 12" deep concrete footings for stability.

Anchoring Procedure Details

Site Preparation and Excavation

Finding a level surface and digging 6" diameter x 12" deep holes.

Concrete Mixing and Pouring

Mixing concrete with water and pouring into holes, half a bag per hole.

Securing Stand to Footings

Anchoring windmill stand to wet concrete using 'L' shaped anchors.

Drying Time and Final Placement

Allowing 24-48 hours for concrete to dry before placing windmill topper.

Limited Warranty and Care Instructions

One Year Limited Warranty

Covers defects in material and workmanship for one year from purchase.

Parts Replacement Policy

Defective or missing parts replaced free for 30 days post-purchase.

Warranty Exclusions

Excludes commercial use, abuse, modification, freeze damage, and improper care.

Proper Care and Maintenance

Recommends lacquer coating every 4-6 months and exterior poly-urethane.

Warranty Voidance and Contact

Power tool use may void warranty; contact customer service for issues.