Lesco Elite Zero Pump

Questions and Answers

B
brittany52Aug 14, 2025
What to do if my Lesco Paint Sprayer will not turn on?
- M
  Mrs. Karen KentAug 14, 2025
  If your Lesco Paint Sprayer isn't turning on, first ensure the battery is correctly inserted and charged. Then, set the power switch to the ON position. If it still doesn't work, the battery may be damaged or overheated, in which case you should replace it or allow it to cool. Also, check if the hose is already pressurized, which might cause the pump to turn off automatically; open the shut-off to see if spraying starts.
A
Alyssa StricklandAug 17, 2025
Why my Lesco Elite Zero Pump turns on but doesn't spray?
- R
  robert12Aug 17, 2025
  If your Lesco Paint Sprayer turns on but doesn't spray, the possible causes are: * The tank may be empty, so add liquid to the tank. * The shut-off may be clogged, so clean the shut-off. * The nozzle may be clogged, so clean the nozzle. * The pump may not be primed yet, so allow time for the pump to prime (up to 30 seconds).
L
Lauren PerryAug 20, 2025
How to fix Lesco Elite Zero Pump Paint Sprayer battery that will not charge?
- H
  Hector WallerAug 21, 2025
  If the battery of your Lesco Paint Sprayer will not charge, check the following: 1. Ensure the charger is correctly plugged into a functioning outlet. 2. If the charger still shows no lights, replace it. 3. If a red light is illuminated without a green light, replace the battery. 4. If a red light is flashing, allow the battery to cool. If red and green lights flash alternately, replace the battery.
W
williambowersAug 25, 2025
What to do if my Lesco Paint Sprayer sprays at low pressure?
- S
  Sean ClarkAug 25, 2025
  If your Lesco Paint Sprayer is spraying at low pressure, the issue might be a clogged shut-off or nozzle, so clean these parts. It is also possible that the pump needs more time to prime; allow up to 30 seconds for priming.
A
annette00Aug 27, 2025
How to troubleshoot a Lesco Elite Zero Pump pump that won't fully prime?
- B
  brandonharveyAug 27, 2025
  If the pump of your Lesco Paint Sprayer won't fully prime, first ensure that the liquid level in the tank is sufficient; add more liquid if it's low. If the pump was run dry before refilling, turn the power switch off, open the shut-off to relieve pressure, and then turn the power switch back on. Chemical residue buildup might also be the cause. In this case, clean the sprayer, and if necessary, repeat with warm water and mild detergent, letting it sit in the pump for up to an hour before rinsing. Also, check the in-tank filter; clean the sprayer and repeat the cleaning process if the filter is improperly installed, missing, or damaged.
R
Ronald CunninghamAug 30, 2025
Why does my Lesco Paint Sprayer have a poor spray pattern?
- J
  Justin CowanAug 30, 2025
  A poor spray pattern from your Lesco Paint Sprayer is usually caused by a partially clogged or damaged nozzle. Try cleaning the nozzle first. If that doesn't solve the problem, replace the nozzle.
C
Cristina RoseSep 3, 2025
What causes a Lesco Elite Zero Pump nozzle to drip after releasing the shut-off lever?
- D
  debra83Sep 3, 2025
  If your Lesco Paint Sprayer nozzle drips after releasing the shut-off lever, it could be due to dirt or debris in the shut-off, so clean the shut-off assembly. Alternatively, there may be a damaged O-ring or seal in the shut-off; in this case, replace the shut-off assembly.
B
Brandy MillerSep 6, 2025
Why is the hose leaking at the shut-off on my Lesco Paint Sprayer?
- S
  sherry98Sep 6, 2025
  If the hose on your Lesco Paint Sprayer is leaking at the shut-off, this is probably because of a cracked, swollen, or faulty hose, or a damaged connection. Replace the shut-off assembly.
S
stacyallenSep 9, 2025
What causes a Lesco Paint Sprayer nozzle tip to leak?
- U
  ustanleySep 10, 2025
  If your Lesco Paint Sprayer nozzle tip leaks, it may be due to a missing flat seal. Install the flat seal behind the nozzle tip. Alternatively, the flat seal may be damaged, so replace the flat seal.