Leuze electronic AMS 348i User Manual

AMS 348i
Optical Laser Measurement System 
PROFINET
TECHNICAL DESCRIPTION
en 01-2011/04 50113340

Leuze electronic AMS 348i Specifications

General

Brand	Leuze electronic
Model	AMS 348i
Category	Analytical Instruments
Language	English

Summary

General Information about AMS 348i

Explanation of Symbols in the Manual

Explains the meaning of symbols used in the manual for warnings and notices.

Declaration of Conformity for AMS 348i

States compliance with European directives and American/Canadian safety standards.

AMS 348i Functions and Applications

Explains how the AMS 348i calculates distances using laser technology and its applications.

Safety Notices for AMS 348i Operation

General Safety Notices and Documentation

General safety instructions including documentation, safety regulations, and repair guidelines.

Applicable Safety Standards for AMS 348i

States that the devices were developed and tested according to applicable safety standards.

Intended Use of the AMS 348i Laser System

Describes the AMS 348i as an absolute measuring system based on laser technology for distance measurement.

Working Safely with the AMS 348i

Details about authorized access, unauthorized modifications, laser safety, and qualified personnel.

Fast Commissioning and Operating Principle

Mounting the AMS 348i Device and Reflector

Instructions for mounting the device and reflector on opposing walls with a clear line-of-sight.

Mounting the AMS 348i Laser Unit

Details on mounting the laser unit using screws and adjusting for alignment.

Mounting the Reflector for AMS 348i

Instructions for mounting the reflector using screws and angling it.

Connecting Voltage Supply to AMS 348i

Explains connecting voltage supply via M12 connectors and programmable switching inputs/outputs.

AMS 348i Display Operation and Navigation

How to read device status and measured values on the display using navigation buttons.

AMS 348i Configuration on PROFINET

Steps for installing GSDML file, assigning network address, and commissioning with Siemens S7 PLC.

Specifications of the AMS 348i Laser Measurement System

General Specifications for the AMS 348i

Detailed technical specifications for measurement, electrical, optical, and interface parameters.

Dimensioned Drawing of the AMS 348i

Provides detailed dimensional drawings of the AMS 348i unit with key dimensions labelled.

Type Overview of AMS 348i Models

Lists different AMS 348i models with their operating ranges, PROFINET interfaces, and part numbers.

Installation and Mounting Procedures

Storage and Transportation Guidelines for AMS 348i

Guidelines for proper storage and transportation of the device, including unpacking instructions.

Mounting the AMS 348i Device

Instructions for mounting the device on plane-parallel walls, ensuring unobstructed line-of-sight.

Optional Mounting Bracket for AMS 348i

Describes an optional mounting bracket for horizontal surface mounting of the AMS 348i.

Recommended Mounting Distances for AMS 348i

Explains minimum parallel spacing between AMS 348i devices and with DDLS 200.

Mounting AMS 348i with Laser Beam Deflector Unit

Information on using deflector units for 90° laser beam deflection and their mounting.

Dimensioned Drawing of US AMS 01 Deflector Unit

Provides dimensioned drawings for the US AMS 01 deflector unit.

Mounting the US 1 OMS Deflector Unit

Instructions for mounting the US 1 OMS deflector unit separately from the AMS 348i.

Reflectors for AMS 348i

General Information on Reflectors

Information about using Leuze electronic reflective tapes and the importance of using specified types.

Description of Reflective Tape Types

Describes the composition and properties of the reflective tape, including protective layers.

Specifications of Self-Adhesive Reflective Foil

Details specifications for self-adhesive reflective tapes, including foil size and temperature resistance.

Specifications of Reflective Tape on Metal Plate

Specifications for reflective tapes affixed to metal plates, including dimensions and weight.

Dimensioned Drawing of Reflective Tape on Metal Plate

Provides dimensioned drawings and table for reflective tapes on metal plates.

Specifications of Heated Reflectors

Details specifications for heated reflective tapes, including voltage, power, and temperature control.

Dimensioned Drawing of Heated Reflectors

Provides dimensioned drawings for heated reflectors with their components.

Selecting Reflector Sizes for AMS 348i

Recommendations for selecting reflector sizes based on operating range and mounting type.

Mounting the Reflector

General guidance for mounting self-adhesive, metal plate, and heated reflectors.

Reflector Alignment for Accurate Measurement

Proper alignment of the reflector with the AMS 348i to ensure accurate measurement.

Table of Reflector Pitches and Spacer Sleeves

A table detailing the correct pitch and spacer sleeve lengths for different reflector types.

Electrical Connections for AMS 348i

Safety Notices for Electrical Connections

Critical safety warnings regarding voltage, qualified electricians, and functional earth connection.

PWR Connection: Voltage Supply and I/O

Details the pin assignment for the PWR connection cable (A-coded) for power and I/O.

PROFINET BUS IN Connection Details

Explains the pin assignments for the PROFINET BUS IN connection (D-coded).

PROFINET BUS OUT Connection Details

Details the pin assignments for the PROFINET BUS OUT connection (D-coded).

Service Interface Connection

Outlines the pin assignments for the service interface (A-coded).

AMS 348i Display and Control Panel

Structure of the Control Panel

Overview of the physical layout of the device's control panel, including display and buttons.

Status Display and Operation Guide

Explains how to interpret status messages and operate the device via the display.

Indicators in the AMS 348i Display

Details the meaning of various indicators, status, and warning messages shown on the display.

Bar Graph Display for Laser Signal Strength

Indicates the strength of the received laser light and status information.

Interface Information on AMS 348i Display

Explains the meaning of LNK0, LNK1, ACT0, ACT1 for Ethernet connection status.

LINK LED for PROFINET Connection Status

Explains the green/orange multicolor LED indicating Ethernet/PROFINET connection status.

AMS 348i Control Buttons and Navigation

Describes the function of UP, DOWN, ESC, and ENTER buttons for navigation and confirmation.

AMS 348i Menu Structure Overview

Overview of main menu structure including device, network, status, parameter, language, and service menus.

Parameter Menu Configuration

Details the Parameter handling and PROFINET submenus for device configuration.

Parameter Handling Submenu Functions

Functions for locking parameters, setting passwords, and resetting to defaults.

PROFINET Submenu Options

Options for activating/deactivating the AMS 348i as a PROFINET participant.

Position Value Submenu Parameters

Parameters for measurement unit, count direction, offset, preset, and error handling.

I/O Submenu Configuration

Configuration options for digital input/output ports I/O 1 and I/O 2, including limit values.

Language Selection Menu for AMS 348i

Explains how to select the display language from available options.

Other Submenu Settings

Settings for heating control, display illumination, contrast, and service RS232.

Service Menu for Diagnostics

Access to status messages, diagnostics, and expanded diagnostics for troubleshooting.

AMS 348i Operation and Parameter Enabling

Step-by-step guide on how to activate parameter enabling for changing device settings.

PROFINET Interface

General Information on PROFINET

Introduces PROFINET-RT, transmission rates, and module organization via GSD files.

Identification and Maintenance Functions (I&M0)

Details the base record I&M0, including manufacturer ID, serial number, and revision information.

PROFINET Star Topology

Describes operating the AMS 348i as a standalone device in a star topology.

PROFINET Linear Topology

Explains connecting multiple AMS 348i devices in a series without a switch.

Wiring Guidelines for PROFINET

Guidelines for CAT 5 Ethernet cabling, M12 to RJ45 transition, and cable configuration.

PROFINET Cable Lengths and Shielding Requirements

Specifies maximum cable lengths and shielding requirements for PROFINET connections.

PROFINET Electrical Connection Details

Details the PROFINET electrical connections using M12 connectors for BUS IN and BUS OUT.

PROFINET Commissioning and Configuration

Discusses PROFINET communication profiles, data exchange, and protocols.

Pre-Commissioning Measures for AMS 348i

Pre-commissioning checks including familiarization, connection verification, and voltage check.

Starting the AMS 348i Device

Instructions for connecting the supply voltage and the device boot-up sequence.

Configuration Steps for Siemens Simatic S7 Control

Outlines the steps for commissioning the AMS 348i with a Siemens S7 PLC.

Preparing the Control System (S7 PLC)

Preparing the control system, assigning IP address, and ensuring data transmission.

Installing the GSD File for AMS 348i

Instructions for loading the GSD file required for configuring IO devices.

Hardware Configuration of S7 PLC for AMS 348i

Steps for hardware configuration, assigning IP address, and device name in the PLC.

Transferring Configuration to IO Controller (S7 PLC)

Activities performed by the PLC after configuration transfer, including connection establishment.

Configuring the Device Name for PROFINET

Details on assigning a unique device name linked to the MAC ID for PROFINET participants.

PROFINET Device Naming Process

Explains the PROFINET device naming process, linking device name to MAC ID.

General Information on PROFINET GSD Files

Explains the role of GSD files in defining AMS 348i functionality and modules.

Overview of AMS 348i GSD Modules

Lists and describes various GSD modules for AMS 348i, including their parameters and I/O.

Detailed Description of PROFINET GSD Modules

Provides detailed descriptions of individual GSD modules, including cross-references.

Module 1: Position Value Parameters

Details parameters for sign, unit, resolution, count direction, and offset for position value.

Module 2: Static Preset Functionality

Explains specifying a preset value that becomes active upon preset teaching.

Module 3: Dynamic Preset Configuration

Allows specifying a preset value that can be adjusted within the control without altering static parameters.

Module 4: I/O 1 Input/Output Configuration

Defines the operation mode for digital input/output I/O 1, including activation and output functions.

Module 5: I/O 2 Input/Output Configuration

Defines the operation mode for digital input/output I/O 2, including activation and output functions.

Module 6: Status and Control Functions

Signals status information of the AMS 348i and allows laser control via master output data.

Module 7: Position Limit Value Range 1

Defines a distance range with lower and upper limits for position monitoring.

Module 8: Position Limit Value Range 2

Defines a second distance range with lower and upper limits for position monitoring.

Module 9: Error Handling Procedures

Parameters for handling temporary errors in value/velocity calculation, including error delay.

Module 10: Velocity Measurement

Outputs current velocity with configured resolution, dependent on count direction and averaging.

Module 11: Static Velocity Limit Value 1

Compares current velocity with stored values within a defined range (start/end).

Module 12: Static Velocity Limit Value 2

Compares current velocity with stored values in a second defined range.

Module 13: Static Velocity Limit Value 3

Compares current velocity with stored values in a third defined range.

Module 14: Static Velocity Limit Value 4

Compares current velocity with stored values in a fourth defined range.

Module 15: Dynamic Velocity Limit Value

Compares current velocity with stored values, activated by Bit 0.0.

Module 16: Velocity Status Reporting

Provides status information for velocity measurement to the PROFINET master.

Module 18: Other Settings

Settings for heating control, display illumination, contrast, and service RS232.

Module 20: Free Resolution Configuration

Allows free scaling of output measurement values for position and velocity.

Diagnostics and Troubleshooting for AMS 348i

Event-Related Diagnostics in PROFINET

PROFINET transmits events as alarms, including process, diagnostic, and maintenance alarms.

State-Related Diagnostics for Maintenance

Alarms entered into the diagnostics buffer for preventative maintenance and low-priority warnings.

Service and Diagnostics Access via AMS 348i Display

How to access diagnostics from the Service menu, including status messages and diagnostics functions.

Status Messages in AMS 348i Ring Memory

Explains status messages stored in a ring memory with details on type, number, reference, and time.

AMS 348i Diagnostics Function and Data Display

How to activate the diagnostics function and interpret recorded data displayed in two fields.

Expanded Diagnostics for Internal Evaluation

Describes the expanded diagnostics menu item for Leuze-internal evaluation purposes.

General Causes of Errors in AMS 348i

Identifies common error causes for device operation.

LINK LED Status for PROFINET Connection

Explains the green/orange multicolor LED indicating Ethernet/PROFINET connection status.

Power LED Error Indicators and Measures

Lists possible error causes for PWR LED states (OFF, flashes red, static red) and their measures.

BUS LED Interface Error Indicators

Lists possible error causes for BUS LED states (OFF, flashes red, static red) and their measures.

Status Display Error Codes and Troubleshooting

Maps display error codes (PLB, ATT, TMP, LSR, ERR) to possible causes and measures.

Type Overview and Accessories for AMS 348i

AMS 348i Type Key Explanation

Explains how to interpret the type designation of the AMS 3xx series devices.

Type Overview of AMS 348i PROFINET Models

Lists different AMS 348i PROFINET models, their ranges, and part numbers.

Overview of Available Reflector Types

Lists various reflector types with their designations, descriptions, and part numbers.

Accessory Mounting Bracket for AMS 348i

Details the mounting bracket for horizontal surfaces with its part number.

Accessory Deflector Units for Laser Beam

Lists deflector units for laser beam deflection with their part numbers.

Accessory M12 Connectors and Converters

Lists M12 connectors and converters with their part numbers.

Ready-Made Cables for Voltage Supply

Provides contact assignment, specifications, and order codes for PWR connection cables.

Ready-Made Cables for PROFINET Connection

Lists ready-made PROFINET cables, their assignments, and connection notices.

Maintenance and Servicing of AMS 348i

General Maintenance Information for AMS 348i

Basic maintenance guidelines, including cleaning the device and reflector.

Repairs and Servicing Procedures

States that repairs must be carried out by the manufacturer and how to contact them.

Disassembling, Packing, and Disposing Guidelines

Instructions for repacking the device and notes on electrical scrap disposal.