Why does my LevelOne WBR-6801 Wireless Router wireless connection keep dropping?
Your LevelOne Wireless Router wireless connection might be unstable due to several factors. Try the following: * Adjust the antenna orientation. * Change the channel on the router, access point, and wireless adapter to avoid interference. * Keep the router away from electrical devices that generate RF noise, such as microwaves, monitors, and electric motors.
What to do if I forgot my LevelOne WBR-6801 encryption key?
If you've forgotten your encryption key for your LevelOne Wireless Router, you can either go back to the advanced settings to set up your encryption key again or reset the router to its default settings.
What can I do if my LevelOne WBR-6801 Wireless Router wireless client can not access the Internet?
If your wireless client can't access the Internet via your LevelOne Wireless Router, here are a few things to check: * Ensure the router is within range of the client. If it is out of range, put the router closer to your client. * Verify the SSID and encryption key are correct. If they are wrong, check the SSID or encryption setting. * Make sure the client is connected to the correct access point.
How to reset LevelOne WBR-6801 to default?
To reset your LevelOne Wireless Router to its default settings: 1. Make sure the router is powered on. 2. Locate the Reset button on the right side. 3. Press and hold the Reset button for 8 seconds, then release. 4. Wait for the router to reboot. Once it restarts, it will be back to the factory default settings.
Why can’t I configure LevelOne Wireless Router even the cable is plugged and the LED is lit?
If you're unable to configure your LevelOne Wireless Router even when the cable is plugged in and the LED is lit, perform a Ping test to ensure the router is responding. Also, ensure that your Ethernet adapter is working and that all network drivers are installed properly.
What can I do if my LevelOne WBR-6801 Wireless Router Ethernet connection does not work properly?
If your Ethernet connection isn't working properly with your LevelOne Wireless Router, try the following: * Make sure the RJ45 cable is securely connected to the router. * Ensure that your Network Interface Card adapter setting is 'Enabled'. * Verify you're not using a crossover Ethernet cable; a patch cable is recommended. * If the connection still fails, reset the router to its default settings.
What can I do if I can’t setup a wireless connection to LevelOne Wireless Router?
If you're having trouble setting up a wireless connection with your LevelOne Wireless Router, consider these steps: * Ensure the SSID and encryption settings are exactly the same on the client device. * Move the router and the wireless client closer to each other to test the connection. * Temporarily disable all security settings like WEP and MAC Address Control. * Try turning off and restarting both the router and the client device. * Confirm that the LEDs on the router are indicating normal operation. * Make sure the IP Address, subnet mask, Router and DNS settings are correctly entered for the network. * Be aware that other wireless devices, home security systems, or even lights can degrade your wireless connection.
Why my LevelOne WBR-6801 3G connection is keep dropping?
If your 3G connection keeps dropping on your LevelOne Wireless Router, check the 3G signal strength from your ISP in your environment; it should be above the middle level.
What can I do if my LevelOne Wireless Router 3G connection is failed even the dongle is plugged?
If your 3G connection fails even with the dongle plugged into your LevelOne Wireless Router: * Ensure you have a validated SIM card inserted in the 3G data card and that your ISP subscription is active. * If you've enabled PIN code check on the SIM card, verify that the PIN code entered on the dial-up page is correct. * Confirm with your ISP that all dial-up settings are correct. * Ensure that a 3G signal from your ISP is available in your current location.
What can I do if my LevelOne Wireless Router can’t recognize my 3G data card even it is plugged?
Your LevelOne Wireless Router might not recognize your 3G data card due to compatibility issues. Check the latest compatibility list to see if your 3G card is supported.
General| Brand | LevelOne |
|---|---|
| Model | WBR-6801 |
| Category | Wireless Router |
| Language | English |
To Next Page
