To Next PageTo Next PageWhy does my LG FWD-14120FD show an imbalance error?
An imbalance error on your LG Washer can occur for several reasons: the load is too small, the appliance isn't level, laundry is bunched to one side, or non-distributable items are in the drum. Check these potential causes to resolve the issue.
What causes a drain error on an LG FWD-14120FD Washer?
A drain error on your LG washer means that water hasn't drained sufficiently within 10 minutes. Check the drain hose for any clogs or kinks that may be preventing proper drainage.
What causes a lock error on my LG FWD-14120FD Washer?
A lock error on your LG Washer can stem from several connection issues or a defective hall sensor. Here are potential causes and solutions: 1. The LEAD WIRE ASSEMBLY connector isn't connected to the STATOR ASSEMBLY connector: Reconnect or repair the connector. 2. Poor electrical contact between connectors in the LEAD WIRE ASSEMBLY and MAIN PWB ASSEMBLY: Reconnect or repair the contact in the connector. 3. The LEAD WIRE ASSEMBLY is cut: Repair the damaged LEAD WIRE ASSEMBLY. 4. The hall sensor is defective: Replace the STATOR ASSEMBLY.
What to do if my LG FWD-14120FD Washer shows a door open error?
A 'door open error' on your LG washer indicates that the Start/Pause button was pressed while the door was open or that the door switch is malfunctioning. Ensure the door is properly closed before starting the cycle. If the issue persists, the door switch may be faulty.
Why is my LG FWD-14120FD Washer showing an overflow error?
An overflow error on your LG washer occurs when too much water enters the tub, triggering an automatic pump-out. This indicates an issue with the water level control.
What does a current error mean on my LG FWD-14120FD Washer?
A current error on your LG Washer can be due to two reasons. It could be a faulty MAIN PWB ASSEMBLY, in which case you should replace it. Alternatively, the winding in the STATOR ASSEMBLY might be short-circuited, requiring replacement of the STATOR ASSEMBLY.
What does a heating error mean on my LG FWD-14120FD?
A heating error on your LG washer indicates that the THERMISTOR is out of order. This component is responsible for monitoring and regulating the water temperature during the wash cycle.
What does sensor pressure S/W error mean on LG FWD-14120FD?
A 'sensor pressure S/W error' on your LG washer indicates that the sensor pressure switch is malfunctioning. This switch is responsible for monitoring the water pressure inside the washer.
General| Drying Capacity | 8 kg |
|---|---|
| Spin Speed | 1400 rpm |
| Noise Level (Spin) | 72 dB |
| Weight | 80 kg |
| Color | White |
| Inverter Motor | Yes |
| Model | FWD-14120FD |
| Smart Features | NFC |
| Type | Front Load Washer |
Highlights features like Jumbo drum, Intelligent Wash System, and Direct Drive.
Explains how fuzzy logic optimizes wash time based on sensors.
Details the water level control using a pressure sensor.
Describes why the door cannot be opened during operation.
Lists and illustrates essential accessories like inlet hose and wrench.
Guides on removing transit bolts, appliance placement, and leveling.
Details connecting the inlet hose, drain hose, and power plug.
Explains child lock and delay finish functions for user control.
Details the Start/Pause button and wash program selector dial.
Covers Time Save, LED display, ON/OFF, options, and temperature selection.
Describes how to select manual wash, rinse, and spin operations.
Provides a detailed chart of wash programs, steps, and timings.
Emphasizes safety precautions and preliminary checks before troubleshooting.
Details the procedure to enter and use the QC test mode for diagnostics.
Explains how to interpret water level frequency readings for troubleshooting.
Lists common error codes, their symptoms, and potential causes.
Provides a step-by-step guide to diagnose and resolve common operational issues.
Guides on how to resolve the 'Door Open Error' symptom.
Provides steps to diagnose and fix drain-related problems.
Offers solutions for problems related to excessive suds during operation.
Explains how to address problems with the softener dispenser.
Details troubleshooting steps for a 'No Power' issue.
Provides troubleshooting guidance for 'No Water Supply' problems.
Guides on fixing issues where detergent is not dispensed correctly.
Offers solutions for problems with the softener not flowing into the dispenser.
Details troubleshooting steps for identifying and resolving abnormal noises.
Provides troubleshooting steps for drain pump and hose malfunctions.
Guides on resolving issues with continuous heating above the set temperature.
Details the steps to disassemble the control panel assembly.
Provides instructions for disassembling the detergent dispenser assembly.
Details the procedure for removing the water inlet valve assembly.
Explains how to remove the main printed circuit board assembly.
Describes how to remove the lower cover of the appliance.
Provides instructions for disassembling the door assembly.
Details the process of removing and reassembling the door gasket.
Explains how to remove the rotor assembly from the motor.
Details the procedure for removing the stator assembly.
Provides instructions for removing the friction damper assembly.
Guides on cleaning the drain pump filter for proper operation.
Details how to remove and install the heater assembly.
Explains how to remove and mount the thermistor.
Provides steps to remove foreign material stuck between the drum and tub.
Lists and illustrates parts related to the cabinet assembly.
Illustrates the exploded view of the control panel and dispenser components.
Shows the exploded view of the drum and tub assembly parts.
