LG OLED55C27LA User Manual

13
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
(Some buttons and services may not be provided depending on models or
regions.)
How to register the Magic Remote
Control
To use the Magic Remote, first pair it with your TV.
1 Put batteries into the Magic Remote and turn the TV on.
2 Point the Magic Remote at your TV and press the Wheel (OK) on the
remote control.
* If the TV fails to register the Magic Remote, try again after turning the TV
off and back on.
How to deregister the Magic Remote
Control
Press the (Back) and (Home) buttons at the same time, for five
seconds, to unpair the Magic Remote with your TV.
* Press and hold the (Home) and (Q. Settings) buttons for more
than 5 seconds to disconnect and re-register the Magic Remote at the same
time.
• It is recommended that an Access Point (AP) be located more than 0.2m
away from the TV. If the AP is installed closer than 0.2m, the Magic remote
control may not perform as expected due to frequency interference.
Using Always Ready
(Depending on model)
You can operate the TV and connect to Bluetooth with direct voice recognition
while the power is off.
* → → [General] → [Always Ready], setting [Enable the function]
to on.
* Pressing the button while watching TV switches the screen to [Always
Ready] that is turned on, and pressing the button once more turns the
screen to [Always Ready] that is turned off.
* Press the (Home) button or the (Back) button to watch TV when
the screen is in [Always Ready] that is turned on.
* Press the Wheel (OK) button to display the wallpaper when the screen
is in [Always Ready] that is turned off, and press the button to watch TV.
Note
• Using Always Ready may increase energy consumption.
• For models with motion sensors, such as G2, if you set screen on with the
motion sensor, the TV will turn on by recognising the motion.
• For more information about the feature, refer to the → →
[Support] → [User Guide] → [Troubleshooting] → [Learn More About
Always Ready].
Connecting Smart Devices using NFC
Tagging
NFC is technology that uses Near Field Communication (13.56MHz), allowing
you to conveniently send and receive information without separate settings. By
bringing a smart device near the NFC-enabled remote control, you can install
the LG ThinQ app and connect the device to the TV.
1 Turn on NFC in the smart device’s settings. To use NFC with Android devices,
set the NFC option to enable ‘read/write tags’ in the smart device's settings.
The NFC settings may vary depending on the device.
2 Bring the smart device near the (NFC) on the remote control. The
required distance for NFC tagging is about 1cm.
3 Follow the instructions to install the LG ThinQ app on your smart device.
4 Retagging the smart device to the remote control allows you to
conveniently access various features on the connected TV through the LG
ThinQ app.
Note
• This feature is available for NFC-enabled smart devices only.
• This feature is only available if the remote control has an NFC logo.
Specifications
Specifications (MR22GN, MR22GA)
Frequency range Output Power (Max.)
Bluetooth 2,400 to 2,483.5MHz 7dBm
NFC
*
13.553 to 13.567MHz -13.27dBuA/m @ 10m
* Only MR22GN

LG OLED55C27LA Specifications

General

Screen shape	Flat
Response time	- ms
Display diagonal	55 \
Display brightness	- cd/m²
Display technology	OLED
Native aspect ratio	-
Native refresh rate	100 Hz
Display diagonal (metric)	139 cm
Tuner type	Digital
Digital signal format system	DVB-C, DVB-S2, DVB-T2
Smart modes	Filmmaker
Operating system version	22
Operating system installed	Web OS
Audio decoders	Dolby Atmos
RMS rated power	40 W
Number of speakers	2
Product color	Silver
Panel mounting interface	300 x 200 mm
Processor cores	4
AMD FreeSync type	FreeSync Premium
Audio formats supported	AAC, AC3, AC4, EAC3, HE-AAC, MP2, MP3, PCM, WMA, apt-X
Video compression formats	HEVC, VP9
Picture processing technology	LG AI Picture Pro
High Dynamic Range (HDR) technology	Cinema HDR, Dolby Vision IQ, High Dynamic Range 10 Pro (HDR10 Pro)
PC in (D-Sub)	No
USB 2.0 ports quantity	3
Ethernet LAN (RJ-45) ports	1
Consumer Electronics Control (CEC)	SimpLink
Programming period	8 day(s)
AC input voltage	100 - 240 V
AC input frequency	56/60 Hz
Energy efficiency scale	A to G
Power consumption (standby)	0.5 W
Power consumption (typical)	- W
Cables included	AC
Package type	Box
Package depth	187 mm
Package width	1360 mm
Package height	810 mm
Package weight	19900 g

Weight and Dimensions

Stand width	470 mm
Depth (with stand)	230 mm
Width (with stand)	1222 mm
Height (with stand)	756 mm
Weight (with stand)	14600 g
Depth (without stand)	45.1 mm
Height (without stand)	703 mm
Weight (without stand)	12700 g