LG WM3460CW User Manual

15PRODUCT OVERVIEW
ENGLISH
Leveling the Washer
The drum of your new washer spins at very high
speeds. To minimize vibration, noise, and unwanted
movement, the oor must be a level, solid surface.
NOTE
• Adjust the leveling feet only as far as necessary to
level the washer. Extending the leveling feet more
than necessary can cause the washer to vibrate.
• Before installing the washer, make sure that the
oor is clean, dry and free of dust, dirt, water and
oil so the washer feet cannot slide easily. Feet
that move or slide on the oor can contribute to
excessive vibration and noise due to poor contact
with the oor.
1
Position the washer in its nal location.
Take special care not to pinch, strain, or crush the
water and drain lines. If you have a carpenter's
level, you can place it across the top of the
washer. The slope beneath the washer should not
exceed 1 inch, and all four leveling feet must rest
rmly on the oor.
Level
1"
2
Adjust the lower leveling feet.
Turn in one direction to raise the washer or the
other direction to lower it.
Raise Lower
3
Tighten the locknuts.
Turn the locknuts counter-clockwise and tighten
them when the washer is level.
Lock nut
Tighten all 4 lock
nuts securely
4
Recheck the washer’s levelness.
Push or rock the top edges of the washer gently
to make sure the washer does not rock. If the
washer rocks, repeat steps 1-3.
CAUTION
• Using the washer without leveling it may cause
excess vibration and noise, leading to a machine
malfunction.
• Extend the leveling feet only to level the washer.
If you extend the leveling feet unnecessarily, it
may cause abnormal vibration of the washer.
Using Non-Skid Pads
If you install the washer on a slippery surface, it
may move because of excessive vibration. Incorrect
leveling may cause malfunction through noise and
vibration. If this occurs, install the non-skid pads
under the leveling feet and adjust the level.
1
Clean the oor to attach the non-skid pads.
Use a dry rag to remove and clean foreign objects
or moisture. If moisture remains, the non-skid
pads may slip.
2
Adjust the level after placing the washer in the
installation area.
3
Place the adhesive side of the non-skid pad
on the oor.
It is most effective to install the non-skid pads
under the front leveling feet. If it is hard to place
the pads under the front leveling feet, place them
under the back leveling feet.
This side up
Adhesive
side
Remove backing
4
Recheck the washer’s levelness.
Push or rock the top edges of the washer gently
to make sure that the washer does not rock. If the
washer rocks, level the washer again.

LG WM3460CW Specifications

General

Style	front load
Color	white
Washer Capacity	4.5 cubic feet
Max Spin Speed	1300 revolutions per minute
Spin Speeds	3
Number of Cycles	10
Cycle Selections	normal, perm. press, heavy duty, delicates, towels, speed wash, bedding, tub clean, whites, downloaded
Options	fresh care, prewash, remote start, delay wash, wi-fi, add garments, coldwash, extra rinse, rinse+spin, child lock, normal, perm. press, heavy duty, delicates, towels, speed wash, bedding, tub clean, whites, downloaded
Noise level	lodecibel quiet operation
Temperature Settings	3
Temperature Selections	hot, warm, cold
Soil Levels	heavy, normal, light
Internal Heater	yes
Control Panel	dial, touchpad
Delay Start / End	yes
Child Lock	yes
Cycle Signal	yes
Steam	no
Dispenser	single load
Smart Home	remote operation, cycle downloads, service notifications, smartdiagnosis, energy monitoring, true
Wi-Fi	wi-fi
Annual Energy Consumption	100 kilowatt hours
Voltage	120 volts
Current	10 amperes

Weight and Dimensions

Depth	30 1/4 inches
Height	39 inches
Width	27 inches
Net Weight	187 pounds