LG WT5680HVA - Page 33

TROUBLESHOOTING 33
BEFORE CALLING FOR SERVICE (confinued)
Washer will not operate
Washer not filling properly
Control panel has powered off due
to inactivity,
Washer is unplugged.
Water supply is turned off.
Controls are not set properly,
Lid is open
Circuit breaker/fuse istripped/
blown,
Control needs to be reset,
START/PAUSE was not pressed
after a cycle was set.
Extremely low water pressure,
Washer is too cold.
Filter clogged,
Inlet hoses may be kinked,
Energy efficiency.
Insufficient water supply,
The washer lid is open.
Hot and cold inlet hoses are
reversed,
Water level is too low.
_i_¸_!i!!!i_!i_!i_!i_!i_i_!!i_i!_i!_i!_i!_!!_i!i!i!ii!!!!;i!!!!i!ii!ii!i_!_!_!_i!_i_!_!i!!_i_i_i_i_!_i_i!_i_i!_i_i!_i_i_i_i_i_i_i_i!_!i_i!_i_iiiiiiii_iiiiii_i_i_ii_ii_ii_iiiiiiiiiiiiiiiiiiii_i_iiiiiiiii_i_iii_i_i_i_i_i_i!i!ii!!i_ii_ii_i!_i!_!ii_i!_i!_i!_i!iiiii_i!ii_i_!i_!!_ii_i_i_i_i_!_!_!!_!i!_i_!!_i_!i!!i!!i!_!i!i_i_ii_ii_ii_ii_iiiii_i_i_ii!ii_ii!ii_i_i_i!_!_i!_!_i_i_i_i_ii_ii_ii_!!!!_i_
This is normal. Press the POWER button to turn the
washer on.
Make sure cord is plugged securely into a working
outlet,
Turn both hot and cold faucets fully on,
Make sure the cycle was set correctly, close the lid
and press the START/PAUSE button.
The washer will not operate if the lid is open, Close
the lid and make sure that nothing is caught under
the lid preventing it from closing completely,
Check house circuit breakers/fuses. Replace fuses
or reset breaker, The washer should be on a dedicat-
ed branch circuit. The washer will resume the cycle
where it stopped once power is restored.
Press the POWER button, then re-select the desired
cycle and press the START/PAUSE button,
Press the POWER button then re-select the desired
cycle and press the START/PAUSE button, The
washer will shut off if the START/PAUSE button is
not pressed within five minutes.
Check another faucet in the house to make sure that
household water pressure is adequate,
If the washer has beer] exposed to temperatures be-
low freezing for an extended period of time, allow
_t to warm up before pressing the POWER button.
Otherwise, the display will not come on.
Make sure the inlet filters on the fill valves are not
clogged, Refer to the filter cleaning instructions,
Check that inlet hoses are not kinked or clogged.
This is a High Efficiency (HE) washer. As a result, the
water level settings for this washer may be different
than for conventional washers,
Make sure that both hot and cold water faucets are
turned on all the way,
The washer will not operate if the lid is open, Close
the lid and make sure that nothing is caught under
the lid preventing it from closing completely,
Check inlet hose connections, Make sure the hot
water supply is connected to the hot inlet valve, and
the cold water supply is connected to the cold inlet
valve.
This is a high efficiency washer. The water will not
normally cover the clothes, The fill level is optimized
for the wash motion to achieve the best wash per-
formance.