7
and will be subject to Translation into other languages of all
and will be subject to All rights on this document are
will not accept responsibility for damage or malfunctions caused by incorrect installation or improper use of products and Users are therefore recommended to read this manual
in the SAFETY INSTRUCTIONS AND WARNINGS With the aim of improving its products,
prior This document conforms to the state of the automation at which it is provided when released for
operator (and will hereinafter be referred to as manufacturer) and the owner of all rights concerning this The Manufacturer’s information
required by Machinery Directive 98/37/EC is given below:
The identity plate bearing the information on the Manufacturer of the operator is to the control The plate the type anddate (month/year) of manufacture of the
For further information on technical or commercial issues and technician call-out and spares requests, Clients may contact the Manufacturer or area representative from which the product was
Any usage differing from that described above is forbidden.
The operator may not be installed or used in potentially explosive environments.
The Fitter must ensure that the environment in which the automation is installed is conform to the operator’s temperature range (see Technical Data chap.).
The operator is not suitable for use on gates with built-in doors unless the automation is prevented from functioning when the door is open.
gates must conform to current European standards and Directives, including EN 12604 and EN
he operator may only be used when in perfect working order and in compliance with the intended use, in the awareness of safety and hazard conditions and in observance with the instructions for installation and
dysfunctions that may pose threats to safety must be eliminated
gate must be stable, properly hung and resistant to (it must not bend during opening and closure
operator cannot compensate for faulty or incorrectly hung
operator may not be used in environments prone to
not use the operator in environmental conditions characterised by harsh atmospheric agents Salty
The Manufacturer declines responsibility for damage or injury caused by non-conformity with the information supplied concerning installation, trial run, use and maintenance contained
The installation, connection, testing, trial run and maintenance of the operator must be performed by a COMPETENT PERSON aided and supervised by a PROFESSIONAL FITTER.
Installation requires a practical and theoretical knowledge of mechanics, electronics and electrics, and of sector laws and standards.
Amateur installation is strictly forbidden as it does not comply with current standards and laws and therefore does not guarantee the safe operation of the automation.
Do not proceed with installation, connection and trial run in the event of doubts or indecision of any kind.
This manual must be read carefully and understood before installing the operator. If doubts arise during installation, contact a PROFESSIONAL FITTER or the MANUFACTURER.
Do not perform adjustments and/or parameter memorisation before installation is complete and only if you have understood the procedures described in this manual.
O
nly mount the operator on gates that are perfectly aligned with the sliding tracks and are properly hung. A gate that is not correctly aligned or hung can cause serious injury and/or damage to the operator.
The Manufacturer declines all responsibility for damage and faults to the operator caused by non-observance of the instructions contained in this
this manual in a safe and easily accessible place so that it can be consulted rapidly when
installation, connection, trial run and usage of the operator, observe all applicable accident prevention and safety
the interests of safety and optimal functioning of the operator, only use original spares, accessories, devices and fastening
o not perform alterations on any operator device or This type of operation may cause The Manufacturer declines all responsibility for damage caused by products that have been
operator should not be used until the setting up procedure described in the STARTING UP chapter has been
hould liquids penetrate inside the operator, disconnect the electricity supply and contact the Manufacturer’s Assistance Service immediately; use of the operator in such conditions may cause hazard
the case of faults or problems that cannot be resolved using the information contained in this manual, contact the Manufacturer’s assistance
operator must be stored in closed, dry places, at room temperatures of between –20 and
the operator away from sources of heat and naked which could damage it and cause malfunctions, or hazard
the operator in a horizontal position, but not resting on the
touch the gate or moving parts when they are in
at a safe distance when the gate is in motion: only pass when the gate is completely open and
children from playing or standing in the vicinity of the gate or the control organs (radio control), the same precautions should be adopted for disabled persons and
the event of malfunctions (noisiness, jerky movements, suspend the use of the automation immediately: failure to observe this rule may entail serious hazards, risks of accidents and/or serious
damage to the gate and the
Contact a PROFESSIONAL FITTER and in the meantime use the gate manually by disconnecting the operator (see the OPERATOR RELEASE
order to maintain the operator in conditions, ensure that the operations indicated in the MAINTENANCE chapter are performed at the frequency indicated by a PROFESSIONAL
hould liquids penetrate inside the operator, disconnect the power supply immediately and contact the Manufacturer’s Assistance Service; the use of the operator in such conditions may cause hazard
a problem arises that cannot be resolved using the information contained in this manual, contact the Manufacturer’s assistance
• Manufacture:
• Address:
• Telephone:
• Telefax:
• http:
• e-mail:
LIFE home integration
Via Sandro Pertini 3/5 – 31014 COLLE UMBERTO (TV) Italia
+ 39 0438 388592
+ 39 0438 388593
www.homelife.it
info@homelife.it
To Next Page
Loading...
Need help?
General
