Lightolier Lytecaster 302MRX User Manual

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
www.lightolier.com © 2008 Philips Group • A0608
Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Lytecaster Recessed Downlighting 302MRX
Page 1 of 1 3 3/4" (95mm) Aperture Low Voltage MR16 12V Standard Frame-In-Kit (Non-IC)
Lightolier is a Philips group brand
Power Pack Cut Out Reflector Trim
302MRX (120V) 3-3/4" (95mm) Accepts most 3-3/4" (95mm) 300 serie trims; see Reflector
Trim specification sheets.
Complete fixture consists of Reflector Trim & Frame-In Kit. Select each separately
Features
1. Mounting Frame: 20ga. galvanized steel. Four slots are positioned 90º
apart to simplify alignment.
2. Mounting Bars: (4) 18 ga. galvanized steel. 13" (330mm) long bars extend
to 27" (686mm), rotatable and lockable, integral T-bar tabs. Spike detail
eliminates the need of additional nailing.
3. Mounting Bars Locking Clip: (1) locks mounting bars in place.
4. Snap-on Socket Cup: 22ga. galvanized steel. Easy snap-on to housing.
5. Socket: Porcelain body ; Two-pin (GX5.3 base) Pre-wired with 18 ga. Teflon
250º leads to junction box.
6. Transformer: 50VA Magnetic, 120 volt primary, nominal 12 volt secondary,
class "H".
7. Thermal Protector: Meets CSA/UL requirements. Insulation, if used,
must be kept 3" (76mm) away from luminaire sides and junction box.
8. Junction Box: 4" (102mm) x 3" (76mm) x 2" (51mm) 18 ga. galvanized steel .
CSA/UL certified for maximum of 8 No. 12 ga. 90º C through branch circuit
conductors. Integral cable clamp permit attachment of non metallic Loomex
without need of additional connectors. Pry-out knock-outs accept BX cable.
Easy access from both sides with snap-on covers.
Accessories
Mounting Bars Extenders: 1964
20" (508mm) long. Set of 2
Mounting Bar Locking Clips: 0098
To lock mounting bars in place after installation. Set of 12.
Labels
Damp or Wet location rated depending on trim used.
12-1/4"
311mm
5-3/4"
146mm
9-1/2"
(244mm)
14"(356mm) MIN.
25"(635mm) MAX.
7"(175mm)

Lightolier Lytecaster 302MRX Specifications

General

Brand	Lightolier
Model	Lytecaster 302MRX
Category	Indoor Furnishing
Language	English

Summary

Product Specifications

Power Pack and Cut Out

Specifies the power pack model and required cut-out size for the fixture.

Reflector Trim Compatibility

Indicates compatibility with 3-3/4" (95mm) 300 serie trims; refers to separate specification sheets.

Product Features

Mounting Frame

20ga. galvanized steel frame with four slots positioned 90º apart for alignment.

Mounting Bars

Four 18 ga. galvanized steel bars, 13" long, extendable to 27", rotatable, lockable, with integral T-bar tabs.

Mounting Bars Locking Clip

A single clip to secure mounting bars in place.

Snap-on Socket Cup

22ga. galvanized steel cup that easily snaps onto the housing.

Socket

Porcelain body with a two-pin (GX5.3 base) socket pre-wired with 18 ga. Teflon leads.

Transformer

50VA Magnetic transformer with 120V primary, 12V secondary, and Class 'H' insulation.

Thermal Protector

Meets CSA/UL requirements. Insulation must be kept 3" (76mm) from sides and junction box.

Junction Box

4"x3"x2" 18 ga. galvanized steel box, CSA/UL certified for up to 8 No. 12 ga. conductors.

Accessories and Labels

Mounting Bar Extenders

20" (508mm) long extenders, sold as a set of 2.

Mounting Bar Locking Clips

Set of 12 clips to lock mounting bars in place after installation.

Labels

Indicates damp or wet location rating depends on the trim used.