Lincoln 1410 - User Manual

To Next Page

Page Number - 1

Model 1410, 1410E

PowerLuber Battery Charger

Series “A”

CHARGER OPERATION

CHARGING THE BATTERY PACK

Before using your PowerLuber for the ﬁrst time, the battery

pack should be charged for 12 hours. If the battery pack is

installed in the PowerLuber, remove it by following instructions

under.

CHARGING PROCEDURE

Make sure power circuit voltage is the same as that shown

on the charger speciﬁcation plate, Connect charger to

power source.

1. Plug the charger into an appropriate outlet before inserting

battery pack.

2. Insert the battery pack into the charger. The red (charg-

ing) light will blink continuously indicating that the charging

process has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and

may be used at this time.

4. The battery pack may be left on the trickle charge until you

are ready to use.

5. Disconnect charger from power source when not in use.

LEAVING THE BATTERY PACK IN THE

CHARGER

The charger and battery pack can be left connected with the red

light glowing indeﬁnitely. The charger will keep the battery pack

fresh and fully charged.

NOTE: A battery pack will slowly lose its charge when kept out

of the charger. If the battery pack has not been kept on main-

tenance charge, it may need to be recharged before use. A

battery pack may also slowly lose its charge if left in a charger

that is not plugged into an appropriate AC source.

As a battery pack approaches the discharged state, you will no-

tice a sharp drop in tool performance. When the tool is unable to

perform the task at hand, it is time to recharge the battery pack.

Recharging the battery pack before this condition is reached

will reduce the total work life of the pack. Discharging the pack

beyond this point can damage the pack.

NOTE: Battery temperature will increase during and shortly after

use. Batteries may not accept a full charge if they are charged

immediately after use. Allow the battery pack to cool to room

temperature before charging for best results.

CAUTION: Vent slots in top and bottom of charger must not be

obstructed. Do not charge battery when temperature is BELOW

32°F (0° C) or ABOVE 104°F (40° C).

120 volts present at charging terminals. Do not probe with

conductive objects. Danger of electric shock or electrocution.

Form 402021

OCT - 2005

INDICATOR LIGHT OPERATION

CHARGE INDICATORS

The charger is designed to detect certain problems that can

arise with battery packs. Problems are indicated by the red

light ﬂashing at a fast rate. If this occurs, re-insert battery pack

into the charger. If the problem persists, try a different bat

tery pack to determine if the charger is O.K. If the new pack

charges correctly, then the original pack is defective and should

be returned to a service center or other collection site for recy-

cling. If the new battery pack elicits the same trouble indication

as the original, have the charger tested at an authorized service

center.

Owner’s Manual for Charger and Batteries

Europe/Africa:

Heinrich-Hertz-Str 2-8

D-69183 Walldorf

Germany

Phone +49.6227.33.0

Fax +49.6227.33.259

Printed in USA

Web site:

lincolnindustrial.com

Americas:

One Lincoln Way

St. Louis, MO 63120-1578

USA

Phone +1.314.679.4200

Fax +1.800.424.5359

Asia/Paciﬁc:

51 Changi Business Park

Central 2

#09-06 The Signature

Singapore 486066

Phone +65.6588.0188

Fax +65.6588.3438

Need help?

Do you have a question about the Lincoln 1410 and is the answer not in the manual?

Summary

Charger Operation

Charging the Battery Pack

Instructions for initial battery pack charging before first use.

Charging Procedure

Steps for connecting the charger and inserting the battery pack.

Indicator Light Operation

Explanation of the charger's indicator light states.

Charge Indicators

How the charger indicates battery pack problems.

Leaving the Battery Pack in the Charger

Battery Maintenance and Care

Notes on maintaining charge, battery discharge, and temperature effects.

Important Charging Notes

Charging Temperature Recommendations

Optimal and limit temperatures for charging battery packs.

Normal Charging Conditions

Warmth during charging is normal; no indication of a problem.

Troubleshooting Charging Issues

Steps to take if the battery pack does not charge properly.

Battery Recharge and Usage

When to recharge and the effect of partial charging.

Product Specifications

Model 1410;1410 E Specifications

Technical details including input voltage, output, time to charge, cord length, and weight.

Safety Instructions for Charger and Batteries

DANGER: Electric Shock Risk

Risk of electric shock from charger terminals and damaged batteries.

General Charging Precautions

Instructions for safe operation, handling cords, and extension cords.

Charger and Battery Pack Handling

Guidelines for safe handling, repair, and maintenance of charger/battery.

Storage and Environmental Conditions

Recommendations for storing and charging in different temperatures and locations.

Prohibited Charging and Disposal

Restrictions on charging other tools and proper battery disposal.

Declaration of Conformity

EMV Directive Compliance

Statement of compliance with EMV directive and applied harmonized standards.

Limited Warranty

Warranty Terms and Conditions

Details of the one-year limited warranty, exclusions, and claim process.

Contact and Service Information

How to find service centers and contact Lincoln Industrial.