Linddana TP Series - User Manual

Questions and Answers

M
Michael WhitakerJul 28, 2025
Why are the rollers on my Linddana Chipper not turning properly?
- K
  Kelsey SantosJul 28, 2025
  The rollers might not be turning properly due to several reasons. It could be that there's too little oil in the hydraulic system, so you should top it up. Alternatively, the flow valve may be unscrewed too far, requiring you to screw it back in. A jammed fixed roller could also be the cause; clean under and behind it. Other potential issues include a clogged bypass valve (clean it), blockage by the shaft speed monitor (increase rotor rotations), or the operating guard being in position 0 (set it to position A).
J
Jonathan RodriguezAug 5, 2025
What to do if the rollers are not drawing adequately on my Linddana Chipper?
- G
  Gabriela BrownAug 5, 2025
  If the rollers on your Linddana Chipper aren't drawing adequately, several factors could be at play. First, ensure there's sufficient flow by unscrewing the flow valve further. Check the V-belts; if they're too slack, tighten them. If the hydraulic oil is too hot, allow the machine to cool down while investigating the cause. Also consider the hydraulic oil's viscosity; if it's too poor, replace it. Other possible causes include a clogged hydraulic filter (replace it), a worn or damaged oil pump (replace it), a defective oil motor (replace it), or a clogged pressure release valve in the control valve (clean it).
K
Kara BrewerAug 12, 2025
How to improve chip quality from my Linddana Chipper?
- J
  Juan WeaverAug 12, 2025
  If you're experiencing unsatisfactory chip quality with your Linddana Chipper, consider these points: The knives may be blunt and need sharpening. The anvil might be worn, requiring you to turn or replace it. If a knife is too worn down, replace it. Also, check the gap between the knife and anvil; if it's too great, adjust it. Finally, ensure the sliver breaker is fitted and not worn; if it is, fit or replace it.
J
Jeremiah OlsonAug 20, 2025
What to do about poor discharge of chips from Linddana Chipper?
- J
  Joseph TaylorAug 20, 2025
  If your Linddana Chipper is experiencing poor chip discharge, several factors could be responsible. Ensure there is sufficient power on the PTO shaft or motor. Check the scraper for wear and replace it if necessary. Similarly, inspect the ejector blades and replace them if they are worn. If there's a blanking plate in the top part, remove it. Lastly, make sure the machine is running at the correct speed by increasing it to maximum revolutions.

Summary

Introduction and Compliance

Product Introduction

Overview of the TP 230 wood chipper and manual contents.

EU Declaration of Conformity

Manufacturer's statement of compliance with relevant EC directives and standards.

Setup and Operation

Usage Guidelines and Assembly

Defines proper application, materials to avoid, and procedures for initial assembly and tractor coupling.

Operating the Wood Chipper

Detailed guidance on starting, running, and controlling the wood chipper's functions and feed rollers.

Safety and Maintenance

Safety Instructions and Pictograms

Essential safety rules, PPE, operational precautions, and explanations of warning symbols.

Maintenance Schedule and Procedures

Schedule of maintenance tasks, lubrication, oil changes, and detailed wear part replacement steps.

Knife Sharpening

Methodology for sharpening knives using wet grinding, correct angles, and minimum width.

TP PILOT Control System

System Operation and Programming

Instructions for general operation, monitoring, and adjusting parameters of the TP PILOT system.

Installation and Technical Data

Diagrams for TP PILOT installation and its technical specifications and operating range.

Support and Specifications

Troubleshooting Common Issues

Guide to diagnosing and resolving common problems with the wood chipper's functions.

Warranty, Technical Data, and Diagrams

Details on warranty coverage, making claims, technical specifications, and hydraulic diagrams.

Accessories and Spare Parts

List of available accessories and reference to the spare parts catalogue.

Linddana TP Series Specifications

General

Brand	Linddana
Model	TP Series
Category	Chipper
Language	English