Need help?Do you have a question about the Line 6 POD HD PRO X and is the answer not in the manual?
General| Modeling Technology | HD Modeling |
|---|---|
| Computer Connectivity | USB |
| Form Factor | Rackmount |
| Width | 19" |
| Depth | 9.5" |
| Type | Guitar Multi-Effects Processor |
| Number of Effects | 100+ effects |
| Amp Modeling | Yes |
| Inputs | 1 x 1/4" (guitar), 1 x XLR (mic), 1 x 1/4" (aux in) |
| Outputs | 2 x 1/4" (main), 2 x XLR (main), 1 x 1/4" (headphones) |
| MIDI I/O | In/Out |
| USB | Yes |
| Sampling Rate | 96 kHz |
| Display | LCD |
| Expression Pedal Input | 1 x 1/4" |
| Dimensions | 19" |
| Power Supply | AC Adapter |
Accesses the device's home screen views for navigation and preset selection.
Displays amp and FX blocks in the current preset's signal chain for editing.
Displays the currently loaded preset number in a large, prominent format.
Shows functions for connected Line 6 FBV controllers, varying by device settings.
Activates the guitar tuner; displays note name and tuning status.
Sets system tempo and refers to Pilot's Guide for I/O details.
Free software for patch editing, librarian functions, and device management.
How to enter the System Setup menu for device configuration options.
Configures footswitch mode, amp knob display, looper display, and view options.
Adjusts LCD contrast, tap tempo LED, AC frequency, and FBV express settings.
Selects audio input sources and adjusts guitar input impedance.
Configures output signal type for direct recording or amplifier connection.
Sets digital output signal format, sample rate, and level for S/PDIF or AES/EBU.
Configures system MIDI channel and tempo sync settings.
Sets Variax control mode (Preset/Global) and tempo sync options.
Allows configuration and saving of alternate tunings for JTV guitars.
Configures audio signal routing to Line 6 DT Series amplifiers via L6 LINK.
Dictates how DT Series amplifiers follow POD HD Pro X amp models and settings.
Details the function and parameters of the 8 FX blocks available per preset.
Describes how to insert and configure the hardware FX Loop within the signal chain.
Covers amp block positioning and mixer block's level/pan controls for parallel paths.
Explains how to reposition FX blocks within the signal chain for routing flexibility.
Details how mono and stereo FX models interact within the signal chain.
How to assign FBV footswitches to remotely toggle Amp or FX Blocks On/Off.
Manages DSP resources dynamically and how to handle DSP limit conditions.
Explains how POD HD Pro X stores and accesses 64 presets within 8 set lists.
How to display the Set Lists screen by pressing the PRESETS knob.
Instructions for loading a set list and renaming it using the SAVE button.
How to view, load, and rearrange presets within a set list.
Details how each preset stores comprehensive settings like FX, amps, and parameters.
Methods to increment through presets using the PRESETS knob or the Set List screen.
Using FBV footswitches to navigate banks and presets.
How to save customized presets, rename them, or move them within set lists.
Explains using knobs to select set list, destination, and rename the preset.
How to enter the FX Edit Mode from the Signal Flow View for detailed parameter editing.
Selecting the FX model type and accessing basic parameters via multi-function knobs.
Choosing specific FX models and editing their parameters using multi-function knobs.
Details editing parameters for the FX Loop, similar to FX models.
Explains placing one or two amp models in pre, post, or parallel paths.
Discusses using a single amp block in pre or post positions within the signal chain.
How to select Amp, Cab, and Mic models using the Signal Flow View and knobs.
Introduces preamp versions of amps, useful for external amplification.
Covers amp block states (On/Off/Disabled) and default model loading.
Lists available mic models for guitar and bass cabinets.
Navigating amp edit screens, including page 1 for model selection and parameters.
Details settings for master volume, sag, bias, and hum/ripple for power amp emulation.
Configuring microphone and speaker cabinet settings within amp edit.
Fine-tuning speaker resonance, thump, and decay for the cab tone.
A comprehensive table of available amp and preamp models and their inspirations.
Explains custom knob labels for specific amp models like Super O and Divide 9/15.
A table listing available cab models and their original speaker cabinet inspirations.
Details parameters for compressor and noise gate FX models.
Lists parameters for various distortion FX models like Screamer and Overdrive.
Overview of modulation FX parameters like speed, depth, and mix.
Details parameters for filter FX like Wah, Vocoder, and Envelope filters.
Covers parameters for pitch-shifting FX like Bass Octaver and Smart Harmony.
Explains parameters for EQ and vintage preamp FX models.
Lists parameters for delay FX like Ping Pong, Digital Delay, and Tape Echo.
Details parameters for reverb FX like Plate, Room, and Spring reverbs.
Covers parameters for wah FX, focusing on position and mix controls.
Explains the looper screen and its functions accessible via FBV controllers.
Details the Undo, Play Once, and Pre/Post position functions of the looper.
Instructions for recording new loops and layering overdubs.
How to play, stop, and change loop playback speed.
Controls for reverse playback and additional looper settings.
Adjusts playback volume, overdub volume, and EQ for loops.
Explains how 1/2 speed affects recording time and playback pitch.
Guide to installing the USB audio driver and Line 6 Monkey software.
How audio signals are routed via USB and the Record Send feature.
Utility for configuring audio driver settings on Mac and Windows.
Specific driver options and settings for Mac users.
Configures record sends and hardware monitor levels in audio settings.
Details the input configuration screen of the Mac Audio MIDI Setup utility.
Explains output settings, default device options, and sample rate/bit depth.
Configuration options for Windows users via the Audio MIDI Devices utility.
Steps to launch the Monkey software and create a user account.
Process for registering your device and checking for available software updates.
Performing firmware updates and managing presets during updates.
Instructions for updating firmware for Line 6 Variax instruments.
Introduction to supported Line 6 FBV controllers for POD HD Pro X.
How to connect FBV devices and configure system setup options for them.
Details footswitch modes, looper display options, and performance view screens.
Explains the default mappings of FBV controllers to POD HD Pro X functions.
Detailed mapping of footswitches for the FBV Shortboard MkII.
Specific footswitch mappings for the looper functions on the Shortboard MkII.
Detailed mapping of footswitches for the FBV Express MkII.
Detailed mapping of footswitches for the FBV Longboard.
Specific footswitch mappings for looper functions on the Longboard.
Detailed mapping of footswitches for the FBV Shortboard.
Specific footswitch mappings for looper functions on the Shortboard.
Explains pedal controllers, expression pedal assignments, and Variax knob assignments.
Steps for assigning expression pedals and Variax knobs to control amp/FX parameters.
How to assign FX or Amp blocks to specific footswitches for toggling On/Off.
Manually assigning functions to the EXP pedal's toe switch.
Accessing and loading set lists using FBV Shortboard or Longboard footswitches.
Using FBV footswitches to set tap tempo and enter tuner mode.
Details MIDI input/output ports and setting the MIDI channel.
Reference table for MIDI CC numbers to control functions like pedals and footswitches.
MIDI CCs for looper functions and additional controls like tap tempo.
How POD HD Pro X responds to MIDI Bank and Program Change messages.
How hardware controls like PRESETS knob and FBV switches send MIDI messages.
Using the device and FBV to control external MIDI hardware or software.
Configuring custom MIDI commands for FBV footswitches and pedals.
Selecting MIDI message types (CC, Program Change, Note On) and their values.
Global MIDI CC assignments automatically transmitted during looper mode.
To Next Page