EasyManua.ls Logo

Linvatec Hall Surgical PowerPro PRO3600 - User Manual

Linvatec Hall Surgical PowerPro PRO3600
40 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
The
P
ower
Pro
®
(PRO3600)
Battery Charger Instruction Manual

Questions and Answers

  • B
    Brandon SmithAug 11, 2025
    How to troubleshoot a non-functioning Linvatec Hall Surgical PowerPro PRO3600 Battery Charger?
    • A
      aaronsimmonsAug 11, 2025
      If the Linvatec Battery Charger (primary or secondary) isn't working, check the following: * Ensure the power cord is correctly plugged in. If it is, try replacing the power cord. * Verify that the battery charger is turned on using the power switch. * Check the fuse and replace it if it's blown. * For the secondary charger, make sure the accessory cord is plugged in. If it is, try replacing the accessory cord. If none of these steps work, the battery charger may be faulty and should be returned for service.
  • N
    nsmithAug 23, 2025
    What does it mean if the LEDs are flashing yellow, green, and red on my Linvatec Battery Charger?
    • C
      Corey LopezAug 25, 2025
      If the Linvatec Battery Charger displays flashing yellow, green, and red LEDs on one or more platforms, it indicates either a bad battery or a system fault. Remove the batteries and cycle the charger power. If the system fault clears, then the battery is bad and needs to be replaced and disposed of properly. If the flashing lights persist after cycling the power, the charger requires servicing.
  • P
    Paul OrtizAug 29, 2025
    What to do if sterile transfer battery won't charge on Linvatec Hall Surgical PowerPro PRO3600?
    • J
      Jason DuarteAug 29, 2025
      If the sterile transfer battery won't begin charging and the red LED is NOT illuminated on your Linvatec Battery Charger, check for the following: Inspect the sterile transfer battery platform, battery, and charger for debris build-up on electrical connections. If found, clean and recharge. Inspect the sterile transfer battery platform, battery, and charger for loose mechanical connections or corrosion on electrical connections. If any of these conditions are found, do not use. If all inspections are normal, dispose of the associated battery properly. If the platform or charger has any of these conditions, have them serviced.
  • M
    Marie SmithSep 4, 2025
    Why no LED illuminates on my Linvatec Hall Surgical PowerPro PRO3600?
    • T
      Tara FloresSep 4, 2025
      If no LED illuminates on the Linvatec Battery Charger, but the green power LED is on, it suggests there may be intermittent or loose mechanical connections, corrosion, debris build-up on electrical connections, or high or low impedance connections or shorts in the equipment (charger, battery, Sterile Transfer Battery Platform, SureCharge Battery Sterilization/ Charging Case). Inspect all equipment for these conditions, and if any are found, do not use the equipment and replace the associated piece of equipment.
  • E
    Erik CampbellNov 16, 2025
    Why is the red LED illuminated on my Linvatec Battery Charger?
    • A
      Amanda StantonNov 16, 2025
      If the red LED illuminates on the Linvatec Battery Charger, it could be due to several reasons: * Ensure the battery pack (PRO3010 or PRO3020) is fully engaged in the charger receptacle. * If using a sterile transfer battery, confirm the platform is fully engaged on the charger and the battery is fully engaged in the platform. * The sterile transfer battery must be removed from the case and charged in the sterile transfer platform. * Inspect all equipment for debris build-up or loose mechanical connections or corrosion on electrical connections. If any of these conditions are found, do not use. If all inspections are normal, dispose of the associated battery properly. * Verify that the SureCharge Battery Sterilization/Charging Case is completely engaged on the battery charger. *...

Linvatec Hall Surgical PowerPro PRO3600 Specifications

General IconGeneral
Input Voltage100-240 V AC
Input Frequency50/60 Hz
Output Voltage14.4 VDC
Output Current1.5 A
Charging Time90 minutes
Operating Temperature10°C to 40°C
Storage Temperature-20°C to 60°C
Battery TypeNiMH
Compatible Battery TypePRO3600 Battery Pack