Loop Telecom Loop-O9500R - Page 5

Loop-O9500 SDH/SONET IMAP
SDH/SONET-MSTP
5
Ordering Information
Note: RoHS compliant units are identified by the letter G appearing immediately at the end of the ordering code.
Model
Description
Notes
Main Unit
Loop-O9500-R-CHA-G
6U height Rack chassis for O9500R
without CPU and power
Loop-O9500-R-CHAA-G
6U height Rack chassis support up to 2.5G Mbps
mapping bandwidth for O9500R
without CPU and power
Controller Modules (CPU)
Loop-O9500-R-CC16-G
Controller module with cross-connect unit and
two STM-1/4/16 (OC-3/12/48) interfaces
without SFP (mini-GBIC) optical modules
· Order two for redundancy.
· Please order SFP optical modules
separately from SFP optical
modules brochure
· Use with Loop-O9500-R-CHAA-G
Loop-O9500-R-CC4-G
Controller module with cross-connect unit and
two STM-1/4 (OC-3/12) interfaces
without SFP (mini-GBIC) optical modules
· Order two for redundancy.
· Please order SFP optical modules
separately from SFP optical
modules brochure
· Use with Loop-O9500-R-CHA-G or
Loop-O9500-R-CHAA-G
Connector Board and Fan Modules
Loop-O9500-R-CBA-G
Connector Board
· CBA or CBB is required for each
chassis.
· If you need order wire function in
CBA, please purchase order wire
phone: Loop-O9500-R-OW under
accessory section.
Loop-O9500-R-CBB-G
Connector Board with EoW using VoIP
technology
· CBA or CBB is required for each
chassis.
· You can use regular analog phone
for order wire function in CBB.
Loop-O9500-R-FANA-G
Fan Board
· One required for each chassis.
High Speed or High Density Tributary Modules
Loop-O9500-R-16TE-G
16 E1 (120 ohm) or 16 T1 software
programmable plug-in card
· The 16/32/63TE modules can also
be used in the Loop-O9400R.
Loop-O9500-R-32TE-G
32 E1 (120 ohm) or 32 T1 software
programmable plug-in card
Loop-O9500-R-63TE-G
63 E1 (120 ohm) or 63 T1 software
programmable plug-in card
Loop-O9500-R-16E75-G
16 E1(75 ohm) plug-in card
· The 16/32/63E75 modules can also
be used in the Loop-O9400R.
Loop-O9500-R-32E75-G
32 E1(75 ohm) plug-in card
Loop-O9500-R-63E75-G
63 E1(75 ohm) plug-in card
Loop-O9500-R-3TE3-G
3 T3 or 3 E3 software programmable interface
plug-in card
· The 3TE3 and 3TE3M13 modules
can also be used in the
Loop-O9400R.
Loop-O9500-R-3TE3M13-G
3 T3 or 3 E3 software programmable interface
plug-in modules with M13 /Mx3 function for T3
interface only
Loop-O9500-R-7FOM-G
7-port Fiber Optical Interface with 7 SFP
housings (SFP not included)
· This card can also be used in the
Loop-O9400R.
· Please order SFP optical modules
separately from SFP optical
modules brochure