LRP electronic SXX StockSpec - User Manual

INSTALLATION TIPS
WIRES & INSTALLATION
CONNECTIONS & EXPLANATIONS
USER MANUAL
SPECIFICATIONS
RADIO- / SPEED-CONTROL SETUP
SPARE- & OPTIONAL-PARTS
A B C + -
C
B
A
• Positionthespeed-controlandcapacitorwheretheyareprotectedintheeventofacrashandgivesyoueasy
accesstotheconnectorsandbuttons.
• Mountthespeedoandcapacitorusingthesuppliedthick/blackdoubled-sidedtape
• Makesurethereisenoughclearancebetweenthespeed-control,power-wires,antennaandreceiver.Avoid
anydirectcontactbetweenpowercomponents,thereceiverortheantennaasthiscancauseinterference.If
interferenceoccurs,positionthecomponentsatadifferentplaceinthemodel.
• Theaerialshouldberunverticallyupandawayfromthereceiver.Avoidcontactwithanypartsmadeofcarbon
fibreormetal.Iftheaerialistoolong,don’tcoiluptheexcesslength.Seealsotheinstructionssuppliedwith
yourradiocontrolsystem.
Receiver Connecting Wire:TheSXX StockSpec
is equipped withan LRP Multicon receiverwire. As
supplied, it will easily fit in all ordinary receivers.
Make sure you connect it to receiver with correct
polarityandusechannel2.
Sensor Connector:locatedunderneaththesolder
tabs. The bi-directional multipole sensor wire con-
nects the speed-control andthe motor.Always use
thesensorwireanddonotalterormodifythiscable!
There are replaceable/optional hall sensor wires
available,pleaserefertocompleteline-upat„Spare-
&Optional-Parts“.
Power Wires: Formaximumperformance,flexible
silicone power wires without any connectors are
used.Theuniquesplittedsolder-tabsalloweasyand
convenient replacement of the power wires. Never-
thelesssomesolderingskillsarerequired.Avoidsol-
deringlongerthen5secpersolderingjointtoprevent
possibledamagetothespeed-controlduetooverhea-
tingofthecomponents!Therearereplacementpower
wires available, please refer to complete line-up at
„Spare-&Optional-Parts“.
Heatsink: Toachievebestperfomanceevenunder
extreme conditions, the heatsink has been directly
mountedtothespeed-control.Thisensuresthebest
possibleheattransferawayfromthespeed-control.
Caution: Never attempt to remove the heatsink or
yourSXX StockSpecmaygetdamagedifyoutrytodo
this.Theheatsinkisanintegralpart,gluedtothefet‘s
andthereforecannotberemoved.
PureBrushlessCompetition yes TwinBEC 6.0V/3.0A
Forward/Brake yes C³Technology yes
Footprint 30.5x33.0mm X-Brake yes
Height 21.0mm HighFrequency yes
Weight(excl.wires) 36.0g SensoredBrushlessSystem yes
VoltageInput 3.7-7.4V Multi-Protection-System2 yes
Typ.VoltageDrop*@20A 0.013V/phase Internal-Temp-CheckSystem3 yes
RatedCurrent* 764A/phase BlueLED yes
Compatiblewindingstyles Star PowerWires 3.3mm²
Rec.MotorLimitwith5cells over4.0T
4adj.Modes (ACS2, Dual ADPC
max
,
Autobrake)
yes
Rec.MotorLimitwith6cells over4.5T
TheSXX StockSpec comessuppliedwithflexible3.3mm²siliconepower-wireswithoutconnectors.Beverycareful
withthecorrectwiresequence/colorssinceanincorrectconnectionmaydamagethespeed-control!Avoidcrea-
tingsolderbridgesonthesolder-tabsandisolateallconnectionscarefully.
Caution:Avoidsolderinglongerthen5secpersolderingjointwhenreplacingthepowerwiresonthespeed-control
andmotortopreventpossibledamageduetooverheatingofthecomponents!
 •Connectthespeed-controltothereceiver(position:Channel2
 •Bluepower-wire  SpeedoMOT.Atomotor„A“
 •Yellowpower-wire  SpeedoMOT.Btomotor„B“
 •Orangepower-wire  SpeedoMOT.Ctomotor„C“
 •Connectthehallsensorcabletothespeed-control(underneaththesolder-tabs)andthemotor.
 •Doublecheckallconnectionsbeforeconnectingthespeed-controltoabattery.
CAUTION: Ifbatteryisconnectedwithreversedpolarityitwilldestroyyourspeed-control!
 •Redpower-wire  SpeedoBAT+tobattery„Plus“
 •Blackpower-wire  SpeedoBAT-tobattery„Minus“
 •Thespeed-controlisnowreadytobeset-up(seesection5).
RA00274
*Transistorsratingat25°CjunctiontemperatureSpecificationssubjecttochangewithoutnotice.
LRPelectronicGmbH
Wilhelm-Enssle-Str.132-134
73630Remshalden,Germany
info@LRP.cc-www.LRP.cc
DearCustomer,
thankyouforyourtrustinthisLRPproduct.BypurchasingaLRP SXX StockSpec brushlessspeed-control,you
have chosen one of the mostadvanced and successful speed-controls oftoday. This speed-controlwith all of
itshigh-techfeaturesandspeciallyselectedelectroniccomponentsisoneofthebestspeed-controlscurrently
availableonthemarket.IFMARWorldChampionTechnology!
 •100%StockRacingBrushlessCompetition •DualADPC
max
PowerProfiles
 •C³(CopperCoreCooling)Technology •TwinBECfor1Sto2SLiPowithoutreceiverpack
 •AutoCellSystem2 •New„X-Brake“
 •Internal-Temp-CheckSystem3 •Multi-ProtectionSystem3
 •Smallfootprint •SensoredDesign
Please read thefollowing instructionscarefullybeforeyoustartusing your speedcontrol.This user guidecontains
importantnotesforthesafety,theuseandthemaintenanceofthisproduct.Thusprotectingyourselfandavoiddamages
oftheproduct.
Proceedaccordingtotheuserguideinordertounderstandyourspeedcontrolbetter.Pleasetakeyourtimeasyouwill
havemuchmorejoywithyourproductifyouknowitexactly.
Thisusermanualshallbekeptinasafeplace.Ifanothercustomerisusingthisproduct,thismanualhastobehanded
outtogetherwithit.
Receiverwire
On/Off-Switch
MOT.C(Orange)
PowerCapacitor
BAT+(Red) MOT.B(Yellow) BAT-(Black) MOT.A(Blue)
SensorConnector
(underneathsoldertabs)
InsetupmodetheSXX StockSpec storeseverystep(e.g.learningyourradiosneutralandendpoints)bypressing
theSETbutton.Allthesettingswillbestoredinthememoryevenifitwillbedisconnectedfromthebattery.
Description othernamesinradio RequiredSetting
ThrottleTravel HighATV,EPA 100%
BrakeTravel LowATV,EPA,ATL 100%
ThrottleExponential EXP,EXPO startwith0
NeutralTrim SUBTrim centre
ServoReverse ThrottleReverse anysetting,don‘tchangeafterset-upprocedure!
TRANSMITTER SETTINGS: Setupthefollowingbasicfunctionsonyourtransmitter(ifavailable):
Ifyourtransmitterdoesn‘tofferanyofabovefunctions,it‘salreadyin„basicsetup“mode.
•Ensurethatthespeed-controlisnotconnectedtothedrivebatteryandisswitchedoff.
•Removemotorpinionorensurethatthewheelsofthemodelarefreetorotate.
•Switchthetransmitteronandsetthetransmitterthrottlesticktoneutral.
•Connectthespeed-controltothebatteryandswitchtheuniton.
•HoldtheSETbuttonpressedforatleast3sec.
YouenteredsetupmodeandtheSETLEDflashesblue(itwillflashuntilthesetupiscompleted).
•LeavetransmitterinneutralpositionandpresstheSETbuttononce.
Neutralsettingisstored,MODELEDflashesyellowandthemotorbeeps.
•HoldfullthrottleontransmitterandpresstheSETbuttononce.
Full-throttlesettingisstored,MODELEDflashesred.
•HoldfullbrakeontransmitterandpresstheSETbuttononce.
Brakesettingisstored,LED‘sglowred(MODE)andblue(SET).
• ThiscompletesthesetupprocedureandyourSXX StockSpec isreadytouse.
• Ifyoumakeamistakeduringthesetupprocedure,don‘tworry:Disconnectthebatteryforabout10secandstart
againfromthefirststep.
• Attheendofeachrunswitchofthecar,andthenswitchoffthetransmitter.
• Atthestartofeachrunswitchonthetransmitterfirst,thenswitchonthecar.
• Forstorageofthecar,disconnectthedrivebatteryatanytime!
Function Status Mode LED Set LED
Neutral --
off
blue
Neutral(when„Boost“=value0) -- flashesblue
Forward
partialthrottle
yellow
off
full blue
Brake
partialbrake
red
off
full blue
CHECKING THE FUNCTIONS: ChecktheLED‘swhenmovingyourthrottlestickandyouwillseeifeverythingis
setupcorrectly.
© LRP electronic GmbH 2010
HallSensorWire
orange
blue
yellow
FanConnector
(Optional)
ORDER.NO.:
80910
Brushless StockSpec Competition
Dual ADPC
max
Power Profiles
TwinBEC 6.0V/3.0A
AutoCell System 2
LRPoffersacomprehensivelineofaccessories,aswellasparticularspare-andoptionalitems.Hereyoufindan
overview,forafullpicturepleasevisitourwebsiteatwww.lrp.cc:
#82505 Power-WireSetBrushless2.6mm²(red,black,blue,orange,yellow)
#82506 Power-WireSetBrushless3.3mm²(red,black,blue,orange,yellow)
#81907 3.3mm²Powerwireblack(1.0m)
#81908 3.3mm²Powerwireblue(1.0m)
#82511 LowProfilecoolingfan
#819307 Sensor-Wire„HighFlex“70mm
#819310 Sensor-Wire„HighFlex“100mm
#819315 Sensor-Wire„HighFlex“150mm
#819320 Sensor-Wire„HighFlex“200mm
#82530 SXXPowercapacitor„WorksTeam“3.7-4.8V
#82531 SXXPowercapacitor„WorksTeam“6.0-7.4V
#82520 RadicalMotorHeatsink+Fan
Team advise: Agoodstartingpointforthebrakesettingonyourradiois80%forallclasses.Makesureyoudothe
radio-setupwithallsettingsontheradioon100%andthendecreasebrakestrengthto80%!
Thecrossed-out wheeledbinmeans thatwithintheEuropeanUnion the productmust betaken
to seperate collection at the product end-of-life. Donot dispose of these products as unsorted
municipalwaste.

Summary

Product Overview and Features

Product Description

Highlights the LRP SXX StockSpec brushless speed-control as an advanced, high-tech, and successful product.

Key Technologies

Lists core technologies like C³ Cooling, AutoCell System 2, Dual ADPCmax, and X-Brake.

Connections and Explanations

Receiver Connecting Wire

Connects the speed-control to the receiver using channel 2, ensuring correct polarity.

Sensor Connector

Connects the speed-control to the motor using a bi-directional multipole sensor wire.

Power Wires

Flexible silicone power wires used for maximum performance, requiring careful soldering.

Heatsink

Integral part of the speed-control for optimal heat transfer, cannot be removed.

Installation Tips

Mounting and Placement

Position speed-control and capacitor for protection and easy access, using provided tape.

Interference Prevention

Ensure clearance between components and avoid direct contact to prevent interference.

Antenna Positioning

Run antenna vertically away from receiver, avoid carbon fiber/metal contact.

Wires and Installation

Speed-Control to Receiver Connection

Connect speed-control to receiver on Channel 2 using specified wire colors.

Motor Connections

Connect speed-control motor wires (A, B, C) to corresponding motor terminals.

Hall Sensor Cable Connection

Connect the hall sensor cable to the speed-control and the motor.

Specifications

Radio;Speed-Control Setup

Transmitter Settings

Configure transmitter functions like Throttle Travel, Brake Travel, and Exponential.

Setup Procedure

Step-by-step guide to set neutral, full throttle, and full brake using the SET button.

Checking Functions

Verify correct setup by observing LED status while moving the throttle stick.

Team Advice

Recommendation for initial brake setting and general practice for running.

Spare and Optional Parts

Troubleshooting Guide

General Troubleshooting

Guidance for common issues like no motor response or incorrect wiring.

Motor Response Issues

Troubleshooting steps for motor not running, running backwards, or slow response.

Speed-Control Performance Issues

Diagnosing problems like overheating, slow speed, or no function after setup.

LED Error Codes

Interpreting LED flashes for specific error conditions and their causes.

Repair Procedures and Limited Warranty

Repair Limitations

Details on what constitutes damage and limitations on warranty claims.

Warranty Service

Information on how to obtain warranty service and return policies.

LRP electronic SXX StockSpec Specifications

General

Brake	Adjustable
Brushed/Brushless	Brushless
Forward/Reverse	Yes
Multi Protection System	Yes
Sensored/Sensorless	Sensored
Type	ESC
Voltage Range	4.8V-7.4V
BEC Output	6V/3A
Cooling	Fan
Protection Features	Overload