Lumex GF8905-1A - User Manual

GF8905-1A-INS-LAB-RevC14 1
GF8905-1A: DELUXE TILT OVERBED TABLE
ASSEMBLY & OPERATION INSTRUCTIONS
PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE USE
Info: The most current version of these instructions can be found online at www.grahamfield.com.
Tools needed: Phillips screwdriver,
9
/16 hex wrench,
5
/16 hex wrench
WARNING: Important!Readandunderstandtheseinstructionsbeforeassemblingorusingthe
GF8905-1AOverbedTable.Ifyoudonotunderstandanypartoftheseinstructions,contacta
healthcareprofessionalfordirectionintheuseofthisproduct.IftheOverbedTableisnotproperly
assembledandadjusted,personalinjuryand/ordamagetotheOverbedTablecouldresult.
WARNING:Ifcomponentsaredamagedormissing,contactyourdealerimmediately.DONOT
usesubstituteparts.UseonlyLumexreplacementparts.Non-Lumexreplacementpartscould
causepersonalinjuryand/ordamagetoOverbedTable.
WARNING:NoticeforCaliforniaCustomers-CaliforniaProposition65WARNING:Thisproduct
containsachemicalknowntotheStateofCaliforniatocausecancerandreproductiveor
developmentalharm.
WARNING:GFHealthProducts,Inc.assumesnoresponsibilityforanydamageorinjurycaused
byimproperassemblyoruseofthisproduct.
UNPACKING
1. Check for obvious damage to the carton or its contents. If damage is evident, notify the carrier and your
Graham-Field authorized distributor.
2. Remove all loose packing from the box. Carefully remove all the components from the carton. Components:
Table top, mast, 6 machine screws, base with 4 casters, 2 hex head bolts, 2 at washers, and 2 metal spacers.
mast mounting plate
mast
machinescrew
(6each)
table top
tabletopbracket
release
paddle
tiltknob
install mast
locknut
(6each)
hexheadbolt
(2each)
spacer(2each)
mastcolumn
washer(2each)
base
table
transitlockscrew
install base
transitlockscrew
release
paddle
locking
casters
tiltknob
remove transit
lock screw
ASSEMBLY(SEEPICTURESABOVE)
WARNING:Donotremovethetransitlockscrewfromthemastbeforethetableiscompletely
assembled;thetabletopcouldrisesuddenlyandcauseseriouspersonalinjury.
WARNING:Donotdisassemblethemast;thiscouldcauseseriouspersonalinjury.
1. Place the table top upside down on work surface.
2. Position the mast above the table top, oriented as shown at left above. Place mast mounting plate on table
top, matching mast mounting plate holes with table top bracket holes.
3. Mount mast to table top: Install machine screws through mast mounting plate holes and table top bracket
holes. Install nuts on screws. Tighten.
4. Place the base upside down above the mast, oriented as shown at center above.
5. Install the two hex head bolts through the washers, spacers, and base, and into the end of the mast column
as shown. Tighten the bolts.

Lumex GF8905-1A Specifications

General

Brand	Lumex
Model	GF8905-1A
Category	Indoor Furnishing
Language	English

Summary

Important Safety and Information

Product Information and Tools

Provides essential product details, including model number and required tools for assembly.

General Safety Warnings

Crucial warnings regarding assembly, use, potential hazards, and compliance with safety regulations.

Unpacking and Component Check

Unpacking Procedure

Instructions for checking carton contents for damage and removing all packing materials carefully.

Table Assembly Instructions

Assembly Safety Precautions

Critical safety warnings to prevent injury during table assembly, especially regarding transit lock screw and mast.

Mounting Mast to Table Top

Attaching the mast to the table top using machine screws and nuts, ensuring proper alignment.

Connecting Base to Mast Column

Securing the base to the mast column using hex bolts, washers, and spacers for structural integrity.

Final Assembly and Setup

Securing Table Assembly

Finalizing table setup by turning it upright and ensuring all components are securely attached before use.

Operating the Overbed Table

Operational Safety Guidelines

Important safety advice for using the table, including weight limits and avoiding tipping hazards.

Table Height and Tilt Adjustment

Instructions for raising, lowering, and tilting the table top to the desired position.

Caster Lock Operation

Guidance on how to lock and unlock the table casters using the step-on locks.

Maintenance and Cleaning

Regular Maintenance Checks

Ensuring the table remains securely assembled by frequently checking nuts and bolts.

Cleaning Instructions

Proper methods for cleaning the table using a damp cloth, mild soap, and water.

Limited Warranty Information

Warranty Scope and Period

Details the duration and coverage of the product warranty for defects in material or workmanship.

Obtaining Warranty Service

Procedure for contacting customer service to authorize and initiate warranty claims.

Warranty Exclusions

Lists conditions and factors not covered by the product warranty, such as misuse or unauthorized repairs.

Additional Notes and Claims

Information on freight claims, short shipments, and other relevant terms and conditions.