GB
23
– Remove any coarse dirt.
– Clean the outside of the device with a damp cloth.
Oil cutting tool
– Clean cutting tool with brush. Then, spray oil on
all sides of the cutting tool.
Troubleshooting
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the ven-
dor. You will save yourself a lot of trouble and possibly
money too.
If you can’t fix the fault yourself, contact your nearest
vendor. Please be aware that any improper repairs
will also invalidate the warranty and additional costs
may be incurred.
Disposal
Disposal of the appliance
A crossed-out wheelie bin icon means: Bat-
teries and rechargeable batteries, electrical
or electronic devices must not be disposed of
with household waste. They may contain
substances that are harmful to the environ-
ment and human health.
Consumers must dispose of waste electrical devices,
spent portable batteries and rechargeable batteries
separately from household waste at an official collec-
tion point to ensure that these items are processed
correctly. Information on returning these items is
available from the seller. Sellers are required to
accept these items free of charge.
Batteries and rechargeable batteries, which
are not permanently installed in waste elec-
trical devices, must be removed prior to dis-
posal and must be disposed of separately.
Lithium batteries and battery packs in all systems
must only be retuned to a collection point when dis-
charged. Batteries must always be protected against
short circuits by covering the poles with adhesive
tape.
All end users are responsible for deleting any per-
sonal data stored on waste devices prior to their dis-
posal.
Disposal of the packaging
The packaging consists of cardboard and
correspondingly marked plastics that can
be recycled.
– Make these materials available for recy-
cling.
Technical data
*) The specified values are emission values and do not necessarily represent
safe workplace values. Although there is a correlation between emission
and immission levels, this cannot be used to infer whether additional safety
measures are necessary or not. Factors which affect the current immission
levels at the workplace, include the type of room, other sources of noise,
e. g. the number of machines operating and other processes taking place in
the vicinity. Permitted workplace values can differ from country to country.
This information is designed to help the user to better assess the dangers
and risks. Determination of noise emission values in accordance with
EN 60335-1 & EN 62841-1.
**) The specified vibration emission value was measured in accordance with a
normed test procedure and can be used in order to compare one tool with
another. The specified vibration emission value can also be used for an
introductory evaluation of the exposure. The vibration emission value may
fluctuate from the specified value during actual use of the power tool. These
fluctuations will depend on the way in which the power tool is used. Try to
keep vibrations to a minimum. One method of reducing the vibration load is,
for example, limiting the length of time you work with the tool. All parts of the
operating cycle must be taken into account for this purpose (for example,
also including times in which the power tool is switched off and times in
which it is switched on, but is running without load). Determination of vibra-
tion emission values in accordance with EN 60335-1, EN 50636-2-94 &
EN 62841-1, EN 62841-4-2.
Accessories
DANGER! Risk of injury! Unprofessional
repairs may mean that your unit will no
longer operate safely. This endangers you
and your environment.
Error/Fault Cause Remedy
Device does not work. Battery not slotted in correctly? Slot battery into place.
Battery pack discharged? Charging the battery pack – p. 22
Battery pack defective? Contact your local vendor.
Is the device defective?
Item number 196022
Idle revolutions 1200 min
-1
Sound power level (L
WA
)* 87 dB(A)
(K = 3 dB(A))
Sound pressure level (L
PA
)* 66 dB(A)
(K = 3 dB(A))
Vibrations** < 3,4 m/s²
(K = 1.5 m/s²)
Weight 2,4 kg
Max. operating duration with a full
2 Ah battery
100 min
Hedge trimmer
Cutting length 200 mm
Border cutter
Cutting width 100 mm
You can find more information about suitable batter-
ies and spare parts of the 1 Power Systems here:
see QR Code
Item number 196022
To Next Page
Loading...
