Need help?Do you have a question about the Mackie S500 and is the answer not in the manual?
Transducer Specifications| low-frequency transducer diameter | 15˝ (381 mm) |
|---|---|
| low-frequency transducer voice coil diameter | 2.5˝ (64 mm) |
| high-frequency driver diaphragm diameter | 1.75˝ (44 mm) |
| high-frequency driver voice coil diameter | 1.75˝ (44 mm) |
| power handling | 30 watts RMS (long term) |
| horn mouth size width | 10.6˝ (269 mm) |
| horn mouth size height | 10.6˝ (269 mm) |
| horn throat size | 1.0˝ (25 mm) |
System Specifications| frequency range | 50 Hz–22 kHz |
|---|---|
| frequency response | 75 Hz–20 kHz |
| horizontal coverage | 75º |
| vertical coverage | 65º |
| directivity factor DI (Q) | 10.93 (12.38) |
| sensitivity | 100 dB |
| rated maximum SPL at 1m | 124 dB long term, 127 dB peak |
| crossover point | 1300 Hz |
| nominal system impedance | 8 ohms |
| power handling | 250 watts RMS |
Physical Properties| height | 32.1˝ (817 mm) |
|---|---|
| front width | 19.1˝ (484 mm) |
| rear width | 13.9˝ (353 mm) |
| depth | 18.1˝ (460 mm) |
| net weight | 75 lbs. (34 kg) |
General guidelines for safe operation, installation, and maintenance of the loudspeaker system.
Warning to prevent fire or electric shock by avoiding exposure to rain or moisture.
Information on potential hearing loss from high noise levels and recommended protection.
Instructions for the correct disposal of the product according to environmental regulations.
Introduction to the S500 Series passive loudspeakers and their features for professional sound systems.
Details on power handling, transducers, enclosure, dispersion, and protection for S500 full-range models.
Details on power handling, woofer, low-pass filter, and enclosure for the S518S subwoofer.
Explanation of icons used in the manual to denote important information and in-depth explanations.
Step-by-step guide for connecting and setting up the S500 Series loudspeakers and amplifier.
Key points to remember for safe operation, shutdown procedures, and record keeping for the loudspeakers.
Diagram illustrating the connection of two S512 loudspeakers with a mixer and power amplifier.
Diagram showing four S515 loudspeakers connected in a daisy-chain configuration with a mixer and amplifier.
Diagram illustrating a system setup with two S512 loudspeakers and two S518S subwoofers.
Guidance on optimal placement of S500 Series loudspeakers for best sound performance and avoiding damage.
Tips for managing room acoustics to improve sound intelligibility and direct sound coverage.
Explanation of the protection circuit for high-frequency drivers and how it resets.
Guidance on avoiding loudspeaker damage, focusing on understanding and preventing audio clipping.
Guidelines for matching amplifier power to S500 Series loudspeakers for optimal performance.
Guidance on diagnosing and resolving common problems like no sound or uneven volume.
Tips for addressing issues with bass response, including polarity and room acoustics.
Troubleshooting steps for distorted sound, incorrect input, and bass level adjustments.
Instructions for maintaining the loudspeakers, including protection from moisture and cold.
Description of 1/4" TS connectors used for unbalanced signals and speaker connections.
Explanation of NL4 connectors for handling higher currents and preventing accidental disconnections.
Guidance on using appropriate speaker wire gauge and type for amplifier connections.
Detailed technical specifications for the Mackie S512 two-way loudspeaker.
Detailed technical specifications for the Mackie S515 two-way loudspeaker.
Detailed technical specifications for the Mackie S525 two-way loudspeaker.
Detailed technical specifications for the Mackie S518S subwoofer.
Information on the limited product warranty, purchase requirements, and how to obtain service.
Resources for help, including website, email, and telephone support contacts.
To Next Page
